材料工程
材料工程
재료공정
JOURNAL OF MATERIALS ENGINEERING
2011年
11期
44-50
,共7页
压力机模座%淬火%有限元模拟
壓力機模座%淬火%有限元模擬
압력궤모좌%쉬화%유한원모의
实测并建立了55NiCrMoV7钢的热物性参数数据库和CCT曲线,基于ABAQUS软件建立了不同冷却介质淬火的热力耦合模型.模拟了大型压力机模座油冷和水冷两种淬火过程,获得了温度场和应力场的演化规律.结合模座上不同位置的冷却速度和CCT曲线预测了工作层的组织状态,并预测了模座上的应力分布.结果表明:采用完全油冷方式将在工作层内产生上贝氏体组织,力学性能无法达到使用要求;而完全水冷方式则可在工作层内得到下贝氏体,但在模座内倒角处存在极大的淬裂危险.在此基础上,提出了双液淬火的热处理工艺,模拟结果显示,水冷30min后转入油冷既可保证工作层理想的组织状态,同时也避免了模座局部位置的淬裂危险.
實測併建立瞭55NiCrMoV7鋼的熱物性參數數據庫和CCT麯線,基于ABAQUS軟件建立瞭不同冷卻介質淬火的熱力耦閤模型.模擬瞭大型壓力機模座油冷和水冷兩種淬火過程,穫得瞭溫度場和應力場的縯化規律.結閤模座上不同位置的冷卻速度和CCT麯線預測瞭工作層的組織狀態,併預測瞭模座上的應力分佈.結果錶明:採用完全油冷方式將在工作層內產生上貝氏體組織,力學性能無法達到使用要求;而完全水冷方式則可在工作層內得到下貝氏體,但在模座內倒角處存在極大的淬裂危險.在此基礎上,提齣瞭雙液淬火的熱處理工藝,模擬結果顯示,水冷30min後轉入油冷既可保證工作層理想的組織狀態,同時也避免瞭模座跼部位置的淬裂危險.
실측병건립료55NiCrMoV7강적열물성삼수수거고화CCT곡선,기우ABAQUS연건건립료불동냉각개질쉬화적열력우합모형.모의료대형압력궤모좌유랭화수랭량충쉬화과정,획득료온도장화응력장적연화규률.결합모좌상불동위치적냉각속도화CCT곡선예측료공작층적조직상태,병예측료모좌상적응력분포.결과표명:채용완전유랭방식장재공작층내산생상패씨체조직,역학성능무법체도사용요구;이완전수랭방식칙가재공작층내득도하패씨체,단재모좌내도각처존재겁대적쉬렬위험.재차기출상,제출료쌍액쉬화적열처리공예,모의결과현시,수랭30min후전입유랭기가보증공작층이상적조직상태,동시야피면료모좌국부위치적쉬렬위험.