中国组织工程研究与临床康复
中國組織工程研究與臨床康複
중국조직공정연구여림상강복
JOURNAL OF CLINICAL REHABILITATIVE TISSUE ENGINEERING RESEARCH
2008年
6期
1063-1066
,共4页
吴岳恒%汤顺清%章庆春%毛萱%成安衡%肖学钧
吳嶽恆%湯順清%章慶春%毛萱%成安衡%肖學鈞
오악항%탕순청%장경춘%모훤%성안형%초학균
玻璃陶瓷%多孔%偏磷酸钙%添加剂%生物材料
玻璃陶瓷%多孔%偏燐痠鈣%添加劑%生物材料
파리도자%다공%편린산개%첨가제%생물재료
目的:偏磷酸钙(calcium metaphosphate,CMP)玻璃陶瓷的多孔性能与许多因素相关,如钙磷比、添加剂含量和烧制温度等.通过改变添加剂含量制备不同孔隙率的CMP玻璃陶瓷,观察其成孔差异和降解性能.方法:实验于2006-01/2007-06在暨南大学生物医学工程系和测试中心完成.采用二次烧结法制备3种不同配方的CMP玻璃陶瓷,其配方的主要差异在于添加剂(由Al2O3、MgO、CaF2按3∶2∶1摩尔比例组成)的含量不同,分别为5.4%,6.0%,6.7%.用分析天平称质量,计算3种样品的吸水率、显气孔率和体积密度.采用X射线衍射仪进行3种样品的晶相分析,扫描电镜观察3种样品的表面形貌.计算3种样品的失质量百分比评价其降解性能.结果:①随着添加剂含量的增加,吸水率和显气孔率增大,体积密度减少.②3种样品的X射线衍射图谱基本无差异,结合PCPDFWIN数据库,可知3种CMP玻璃陶瓷的主晶相均为β-Ca(PO3)2晶体.扫描电镜结果表明,随着添加剂含量的增加,样品孔洞数目减少,孔洞直径越来越大.③随着添加剂含量的增加,3种样品的失重百分比分别为7.7%,5.9%和3.4%.结论:通过改变添加剂的含量,可改变钙磷比相同的CMP玻璃陶瓷的多孔性能和降解性能.
目的:偏燐痠鈣(calcium metaphosphate,CMP)玻璃陶瓷的多孔性能與許多因素相關,如鈣燐比、添加劑含量和燒製溫度等.通過改變添加劑含量製備不同孔隙率的CMP玻璃陶瓷,觀察其成孔差異和降解性能.方法:實驗于2006-01/2007-06在暨南大學生物醫學工程繫和測試中心完成.採用二次燒結法製備3種不同配方的CMP玻璃陶瓷,其配方的主要差異在于添加劑(由Al2O3、MgO、CaF2按3∶2∶1摩爾比例組成)的含量不同,分彆為5.4%,6.0%,6.7%.用分析天平稱質量,計算3種樣品的吸水率、顯氣孔率和體積密度.採用X射線衍射儀進行3種樣品的晶相分析,掃描電鏡觀察3種樣品的錶麵形貌.計算3種樣品的失質量百分比評價其降解性能.結果:①隨著添加劑含量的增加,吸水率和顯氣孔率增大,體積密度減少.②3種樣品的X射線衍射圖譜基本無差異,結閤PCPDFWIN數據庫,可知3種CMP玻璃陶瓷的主晶相均為β-Ca(PO3)2晶體.掃描電鏡結果錶明,隨著添加劑含量的增加,樣品孔洞數目減少,孔洞直徑越來越大.③隨著添加劑含量的增加,3種樣品的失重百分比分彆為7.7%,5.9%和3.4%.結論:通過改變添加劑的含量,可改變鈣燐比相同的CMP玻璃陶瓷的多孔性能和降解性能.
목적:편린산개(calcium metaphosphate,CMP)파리도자적다공성능여허다인소상관,여개린비、첨가제함량화소제온도등.통과개변첨가제함량제비불동공극솔적CMP파리도자,관찰기성공차이화강해성능.방법:실험우2006-01/2007-06재기남대학생물의학공정계화측시중심완성.채용이차소결법제비3충불동배방적CMP파리도자,기배방적주요차이재우첨가제(유Al2O3、MgO、CaF2안3∶2∶1마이비례조성)적함량불동,분별위5.4%,6.0%,6.7%.용분석천평칭질량,계산3충양품적흡수솔、현기공솔화체적밀도.채용X사선연사의진행3충양품적정상분석,소묘전경관찰3충양품적표면형모.계산3충양품적실질량백분비평개기강해성능.결과:①수착첨가제함량적증가,흡수솔화현기공솔증대,체적밀도감소.②3충양품적X사선연사도보기본무차이,결합PCPDFWIN수거고,가지3충CMP파리도자적주정상균위β-Ca(PO3)2정체.소묘전경결과표명,수착첨가제함량적증가,양품공동수목감소,공동직경월래월대.③수착첨가제함량적증가,3충양품적실중백분비분별위7.7%,5.9%화3.4%.결론:통과개변첨가제적함량,가개변개린비상동적CMP파리도자적다공성능화강해성능.