材料工程
材料工程
재료공정
JOURNAL OF MATERIALS ENGINEERING
2006年
9期
45-48
,共4页
激光熔覆%NiCrBSiC合金%显微组织%摩擦磨损性能
激光鎔覆%NiCrBSiC閤金%顯微組織%摩抆磨損性能
격광용복%NiCrBSiC합금%현미조직%마찰마손성능
采用横流CO2激光在45钢和TC4钛合金表面熔覆NiCrBSiC合金涂层,利用XRD,SEM和TEM分析了激光熔覆层的微观组织,测试了激光熔覆层的硬度和摩擦磨损性能.结果表明,NiCrBSiC合金激光熔覆层的组织和性能与基底材料的种类密切相关.45钢表面激光熔覆层由γ-Ni,Ni3B,Cr7C3和CrB相组成,硬度在HV800~900之间;TC4合金表面激光熔覆层由γ-Ni,Ni3B,TiC和TiB2相组成,硬度在HV900~1100之间.TC4合金表面NiCrBSiC激光熔覆层的摩擦系数和质量磨损率分别低于45钢表面NiCrBSiC激光熔覆层的摩擦系数和质量磨损率.
採用橫流CO2激光在45鋼和TC4鈦閤金錶麵鎔覆NiCrBSiC閤金塗層,利用XRD,SEM和TEM分析瞭激光鎔覆層的微觀組織,測試瞭激光鎔覆層的硬度和摩抆磨損性能.結果錶明,NiCrBSiC閤金激光鎔覆層的組織和性能與基底材料的種類密切相關.45鋼錶麵激光鎔覆層由γ-Ni,Ni3B,Cr7C3和CrB相組成,硬度在HV800~900之間;TC4閤金錶麵激光鎔覆層由γ-Ni,Ni3B,TiC和TiB2相組成,硬度在HV900~1100之間.TC4閤金錶麵NiCrBSiC激光鎔覆層的摩抆繫數和質量磨損率分彆低于45鋼錶麵NiCrBSiC激光鎔覆層的摩抆繫數和質量磨損率.
채용횡류CO2격광재45강화TC4태합금표면용복NiCrBSiC합금도층,이용XRD,SEM화TEM분석료격광용복층적미관조직,측시료격광용복층적경도화마찰마손성능.결과표명,NiCrBSiC합금격광용복층적조직화성능여기저재료적충류밀절상관.45강표면격광용복층유γ-Ni,Ni3B,Cr7C3화CrB상조성,경도재HV800~900지간;TC4합금표면격광용복층유γ-Ni,Ni3B,TiC화TiB2상조성,경도재HV900~1100지간.TC4합금표면NiCrBSiC격광용복층적마찰계수화질량마손솔분별저우45강표면NiCrBSiC격광용복층적마찰계수화질량마손솔.