热能动力工程
熱能動力工程
열능동력공정
JOURNAL OF ENGINEERING FOR THERMAL ENERGY AND POWER
2007年
6期
673-676
,共4页
液膜模型%破裂%喷射角%平均粒径
液膜模型%破裂%噴射角%平均粒徑
액막모형%파렬%분사각%평균립경
建立了一个喷淋脱硫塔喷嘴数值模型,研究了影响喷淋脱硫塔内气液传质的喷淋液流量与液膜平均破裂长度、喷嘴初始喷射角、液滴平均粒径的关系.设计了专门的测试平台和单匝螺旋喷嘴,采用快速CCD和数码照相机拍照对液膜和液滴运动进行了测试和分析.模型计算和实验结果均表明:液膜平均破裂长度随喷淋液流量加大而减小;液滴平均粒径减小随喷淋液流量加大而减小;在喷嘴出口缝隙高度等于4.25 mm时,随流量的增大,喷嘴的喷射角随流量的增大反而变小,大于4.25 mm后,在同一喷嘴缝隙高度下,喷射角随喷嘴流量的增加而增加.
建立瞭一箇噴淋脫硫塔噴嘴數值模型,研究瞭影響噴淋脫硫塔內氣液傳質的噴淋液流量與液膜平均破裂長度、噴嘴初始噴射角、液滴平均粒徑的關繫.設計瞭專門的測試平檯和單匝螺鏇噴嘴,採用快速CCD和數碼照相機拍照對液膜和液滴運動進行瞭測試和分析.模型計算和實驗結果均錶明:液膜平均破裂長度隨噴淋液流量加大而減小;液滴平均粒徑減小隨噴淋液流量加大而減小;在噴嘴齣口縫隙高度等于4.25 mm時,隨流量的增大,噴嘴的噴射角隨流量的增大反而變小,大于4.25 mm後,在同一噴嘴縫隙高度下,噴射角隨噴嘴流量的增加而增加.
건립료일개분림탈류탑분취수치모형,연구료영향분림탈류탑내기액전질적분림액류량여액막평균파렬장도、분취초시분사각、액적평균립경적관계.설계료전문적측시평태화단잡라선분취,채용쾌속CCD화수마조상궤박조대액막화액적운동진행료측시화분석.모형계산화실험결과균표명:액막평균파렬장도수분림액류량가대이감소;액적평균립경감소수분림액류량가대이감소;재분취출구봉극고도등우4.25 mm시,수류량적증대,분취적분사각수류량적증대반이변소,대우4.25 mm후,재동일분취봉극고도하,분사각수분취류량적증가이증가.