热加工工艺
熱加工工藝
열가공공예
HOT WORKING TECHNOLOGY
2011年
24期
44-46,49
,共4页
轴承钢%精炼工艺%非金属夹杂物
軸承鋼%精煉工藝%非金屬夾雜物
축승강%정련공예%비금속협잡물
针对淮钢80t转炉-90tLF- 100tRH-CC工艺生产的GCr15轴承钢,采用金相、SEM和EDS等方法,研究了精炼过程中夹杂物的尺寸、成分和形貌等的变化情况.经分析计算,得出了各工序夹杂物的成分图,并分析了夹杂物在冶炼过程中的变化规律.结果表明,在LF炉精炼后,微观夹杂物由23.34个/mm2下降到14.02个/mm2;经RH循环脱气处理后,夹杂物有所减少,成材中,夹杂物数量略有减少;随着冶炼过程的进行,大颗粒夹杂在钢包中随着钢流的运动得到了有效去除,细微夹杂物所占比例逐步升高;钢中存在的夹杂物主要有氧化物、硫化物以及CaO(CaS)-Al2O3-MgO类复合夹杂物.
針對淮鋼80t轉爐-90tLF- 100tRH-CC工藝生產的GCr15軸承鋼,採用金相、SEM和EDS等方法,研究瞭精煉過程中夾雜物的呎吋、成分和形貌等的變化情況.經分析計算,得齣瞭各工序夾雜物的成分圖,併分析瞭夾雜物在冶煉過程中的變化規律.結果錶明,在LF爐精煉後,微觀夾雜物由23.34箇/mm2下降到14.02箇/mm2;經RH循環脫氣處理後,夾雜物有所減少,成材中,夾雜物數量略有減少;隨著冶煉過程的進行,大顆粒夾雜在鋼包中隨著鋼流的運動得到瞭有效去除,細微夾雜物所佔比例逐步升高;鋼中存在的夾雜物主要有氧化物、硫化物以及CaO(CaS)-Al2O3-MgO類複閤夾雜物.
침대회강80t전로-90tLF- 100tRH-CC공예생산적GCr15축승강,채용금상、SEM화EDS등방법,연구료정련과정중협잡물적척촌、성분화형모등적변화정황.경분석계산,득출료각공서협잡물적성분도,병분석료협잡물재야련과정중적변화규률.결과표명,재LF로정련후,미관협잡물유23.34개/mm2하강도14.02개/mm2;경RH순배탈기처리후,협잡물유소감소,성재중,협잡물수량략유감소;수착야련과정적진행,대과립협잡재강포중수착강류적운동득도료유효거제,세미협잡물소점비례축보승고;강중존재적협잡물주요유양화물、류화물이급CaO(CaS)-Al2O3-MgO류복합협잡물.