中国表面工程
中國錶麵工程
중국표면공정
CHINA SURFACE ENGINEERING
2012年
1期
65-70
,共6页
董晓焕%张振云%李琼伟%王豫跃%龚永锋%孙腾飞
董曉煥%張振雲%李瓊偉%王豫躍%龔永鋒%孫騰飛
동효환%장진운%리경위%왕예약%공영봉%손등비
高速电弧喷涂%Al/1Cr13复合涂层%组织结构%孔隙率
高速電弧噴塗%Al/1Cr13複閤塗層%組織結構%孔隙率
고속전호분도%Al/1Cr13복합도층%조직결구%공극솔
用高速电弧喷涂制备Al/1Cr13复合涂层,采用3因素3水平正交试验法系统研究了电弧电流、电弧电压和喷涂距离对复合涂层的组织结构、孔隙率和氧含量的影响规律.采用扫描电镜对复合涂层的显微组织和孔隙率进行表征,采用氧氮含量分析仪测得涂层的氧含量.结果表明,在第9组喷涂参数即电孤电流为240 A,电压为32 V,喷涂距离为150 mm的条件下制备的高速电弧喷涂Al/1Cr13复合涂层组织较致密,Al和1Cr13涂层的孔隙率最低分别为1.6%和2.2%.Al涂层氧含量显著低于1Cr13涂层,最低约为2%.
用高速電弧噴塗製備Al/1Cr13複閤塗層,採用3因素3水平正交試驗法繫統研究瞭電弧電流、電弧電壓和噴塗距離對複閤塗層的組織結構、孔隙率和氧含量的影響規律.採用掃描電鏡對複閤塗層的顯微組織和孔隙率進行錶徵,採用氧氮含量分析儀測得塗層的氧含量.結果錶明,在第9組噴塗參數即電孤電流為240 A,電壓為32 V,噴塗距離為150 mm的條件下製備的高速電弧噴塗Al/1Cr13複閤塗層組織較緻密,Al和1Cr13塗層的孔隙率最低分彆為1.6%和2.2%.Al塗層氧含量顯著低于1Cr13塗層,最低約為2%.
용고속전호분도제비Al/1Cr13복합도층,채용3인소3수평정교시험법계통연구료전호전류、전호전압화분도거리대복합도층적조직결구、공극솔화양함량적영향규률.채용소묘전경대복합도층적현미조직화공극솔진행표정,채용양담함량분석의측득도층적양함량.결과표명,재제9조분도삼수즉전고전류위240 A,전압위32 V,분도거리위150 mm적조건하제비적고속전호분도Al/1Cr13복합도층조직교치밀,Al화1Cr13도층적공극솔최저분별위1.6%화2.2%.Al도층양함량현저저우1Cr13도층,최저약위2%.