中国表面工程
中國錶麵工程
중국표면공정
CHINA SURFACE ENGINEERING
2012年
2期
97-102
,共6页
刘蕴锋%朱永伟%刘平%刘婷婷
劉蘊鋒%硃永偉%劉平%劉婷婷
류온봉%주영위%류평%류정정
包覆%非均匀形核%二硫化钼%亲水性%Ni-P- MoS2%复合镀层
包覆%非均勻形覈%二硫化鉬%親水性%Ni-P- MoS2%複閤鍍層
포복%비균균형핵%이류화목%친수성%Ni-P- MoS2%복합도층
采用非均匀形核法将Al2O3包覆到MoS2颗粒表面,提高颗粒的亲水性能.研究了溶液pH值、Al(NO3)3的摩尔浓度和预处理工艺对包覆率的影响;采用SEM及EDS分析了包覆前后MoS2颗粒的微观形貌和表面成分;通过测量接触角研究了颗粒表面的亲水性.结果表明,颗粒表面均匀包覆了一层Al(OH)3;溶液pH值对包覆率的影响最大,Al(NO3)3的摩尔浓度次之.最佳工艺为:溶液pH值为5.5,Al(NO3)3浓度为0.15 mol/L,预处理过程不添加表面活性剂.随着包覆率的提高,MoS2颗粒的亲水性提高.利用包覆Al2O3的MoS2制得了Ni-P-MoS2化学复合镀层,提高了镀层中沉积粒子的均匀致密性.
採用非均勻形覈法將Al2O3包覆到MoS2顆粒錶麵,提高顆粒的親水性能.研究瞭溶液pH值、Al(NO3)3的摩爾濃度和預處理工藝對包覆率的影響;採用SEM及EDS分析瞭包覆前後MoS2顆粒的微觀形貌和錶麵成分;通過測量接觸角研究瞭顆粒錶麵的親水性.結果錶明,顆粒錶麵均勻包覆瞭一層Al(OH)3;溶液pH值對包覆率的影響最大,Al(NO3)3的摩爾濃度次之.最佳工藝為:溶液pH值為5.5,Al(NO3)3濃度為0.15 mol/L,預處理過程不添加錶麵活性劑.隨著包覆率的提高,MoS2顆粒的親水性提高.利用包覆Al2O3的MoS2製得瞭Ni-P-MoS2化學複閤鍍層,提高瞭鍍層中沉積粒子的均勻緻密性.
채용비균균형핵법장Al2O3포복도MoS2과립표면,제고과립적친수성능.연구료용액pH치、Al(NO3)3적마이농도화예처리공예대포복솔적영향;채용SEM급EDS분석료포복전후MoS2과립적미관형모화표면성분;통과측량접촉각연구료과립표면적친수성.결과표명,과립표면균균포복료일층Al(OH)3;용액pH치대포복솔적영향최대,Al(NO3)3적마이농도차지.최가공예위:용액pH치위5.5,Al(NO3)3농도위0.15 mol/L,예처리과정불첨가표면활성제.수착포복솔적제고,MoS2과립적친수성제고.이용포복Al2O3적MoS2제득료Ni-P-MoS2화학복합도층,제고료도층중침적입자적균균치밀성.