铸造
鑄造
주조
FOUNDRY
2011年
9期
899-902
,共4页
毛双亮%水恒勇%陈闪闪%赵爱民
毛雙亮%水恆勇%陳閃閃%趙愛民
모쌍량%수항용%진섬섬%조애민
低合金耐磨钢%热处理%贝/马氏体复相组织%硬度%冲击韧度
低閤金耐磨鋼%熱處理%貝/馬氏體複相組織%硬度%遲擊韌度
저합금내마강%열처리%패/마씨체복상조직%경도%충격인도
研究了一种新型Mn-Cr-Mo-Ni-Cu-RE多元低合金耐磨钢的热处理工艺,利用热膨胀实验测量试验钢的Ae1、Ac3、Ms、Mf等相变温度,借助光学显微镜、扫描电镜、透射电镜等手段,研究了钢的显微组织和断口形貌,测量力学性能,考察热处理工艺对钢的力学性能的影响.研究结果表明,试验钢的相变温度为Ac1=770℃、Ac3=820℃、Ms=340℃、Mf=265℃,经900℃淬火及230℃回火后获得贝/马氏体复相组织,试验钢具有良好的综合力学性能、高强度和高韧性,其硬度达到HRC 52,冲击韧度αKU达到40 J·cm-2.
研究瞭一種新型Mn-Cr-Mo-Ni-Cu-RE多元低閤金耐磨鋼的熱處理工藝,利用熱膨脹實驗測量試驗鋼的Ae1、Ac3、Ms、Mf等相變溫度,藉助光學顯微鏡、掃描電鏡、透射電鏡等手段,研究瞭鋼的顯微組織和斷口形貌,測量力學性能,攷察熱處理工藝對鋼的力學性能的影響.研究結果錶明,試驗鋼的相變溫度為Ac1=770℃、Ac3=820℃、Ms=340℃、Mf=265℃,經900℃淬火及230℃迴火後穫得貝/馬氏體複相組織,試驗鋼具有良好的綜閤力學性能、高彊度和高韌性,其硬度達到HRC 52,遲擊韌度αKU達到40 J·cm-2.
연구료일충신형Mn-Cr-Mo-Ni-Cu-RE다원저합금내마강적열처리공예,이용열팽창실험측량시험강적Ae1、Ac3、Ms、Mf등상변온도,차조광학현미경、소묘전경、투사전경등수단,연구료강적현미조직화단구형모,측량역학성능,고찰열처리공예대강적역학성능적영향.연구결과표명,시험강적상변온도위Ac1=770℃、Ac3=820℃、Ms=340℃、Mf=265℃,경900℃쉬화급230℃회화후획득패/마씨체복상조직,시험강구유량호적종합역학성능、고강도화고인성,기경도체도HRC 52,충격인도αKU체도40 J·cm-2.