应用激光
應用激光
응용격광
APPLIED LASER
2003年
4期
201-204
,共4页
余菊美%晁明举%梁二军%袁斌
餘菊美%晁明舉%樑二軍%袁斌
여국미%조명거%량이군%원빈
激光熔覆%铁基合金%TiO2%裂纹%显微组织%耐磨性
激光鎔覆%鐵基閤金%TiO2%裂紋%顯微組織%耐磨性
격광용복%철기합금%TiO2%렬문%현미조직%내마성
在45#钢基底上进行了铁基合金和铁基合金加TiO2的激光熔覆对比实验.采用渗透法观察熔覆层表面裂纹,利用金相显微镜和扫描电镜观察熔覆层横断面的显微组织,使用X射线衍射仪对熔覆层进行物相分析,并测试了熔覆层横断面的硬度分布和熔覆层的摩擦磨损性能.结果表明,在一定的工艺条件下,添加适量的TiO2,可以获得成形良好、无裂纹、组织致密均匀、耐磨性好的高质量铁基激光熔覆层.适量的TiO2可使涂层共晶体数目增多且分布均匀,组织细化,裂纹消失,在降低涂层裂纹敏感性的同时仍保持涂层的硬度和耐磨性不降低.TiO2对铁基熔覆层性能改善的原因是:适量TiO2的加入,在涂层中可形成Cr13Fe35Ni13Ti7金属间化合物,熔覆层组织由亚共晶组织转变为性能较好的伪共晶组织,且由于高熔点的Ti硼化物的析出,提高了形核率,使组织颗粒细化、均匀.
在45#鋼基底上進行瞭鐵基閤金和鐵基閤金加TiO2的激光鎔覆對比實驗.採用滲透法觀察鎔覆層錶麵裂紋,利用金相顯微鏡和掃描電鏡觀察鎔覆層橫斷麵的顯微組織,使用X射線衍射儀對鎔覆層進行物相分析,併測試瞭鎔覆層橫斷麵的硬度分佈和鎔覆層的摩抆磨損性能.結果錶明,在一定的工藝條件下,添加適量的TiO2,可以穫得成形良好、無裂紋、組織緻密均勻、耐磨性好的高質量鐵基激光鎔覆層.適量的TiO2可使塗層共晶體數目增多且分佈均勻,組織細化,裂紋消失,在降低塗層裂紋敏感性的同時仍保持塗層的硬度和耐磨性不降低.TiO2對鐵基鎔覆層性能改善的原因是:適量TiO2的加入,在塗層中可形成Cr13Fe35Ni13Ti7金屬間化閤物,鎔覆層組織由亞共晶組織轉變為性能較好的偽共晶組織,且由于高鎔點的Ti硼化物的析齣,提高瞭形覈率,使組織顆粒細化、均勻.
재45#강기저상진행료철기합금화철기합금가TiO2적격광용복대비실험.채용삼투법관찰용복층표면렬문,이용금상현미경화소묘전경관찰용복층횡단면적현미조직,사용X사선연사의대용복층진행물상분석,병측시료용복층횡단면적경도분포화용복층적마찰마손성능.결과표명,재일정적공예조건하,첨가괄량적TiO2,가이획득성형량호、무렬문、조직치밀균균、내마성호적고질량철기격광용복층.괄량적TiO2가사도층공정체수목증다차분포균균,조직세화,렬문소실,재강저도층렬문민감성적동시잉보지도층적경도화내마성불강저.TiO2대철기용복층성능개선적원인시:괄량TiO2적가입,재도층중가형성Cr13Fe35Ni13Ti7금속간화합물,용복층조직유아공정조직전변위성능교호적위공정조직,차유우고용점적Ti붕화물적석출,제고료형핵솔,사조직과립세화、균균.