热固性树脂
熱固性樹脂
열고성수지
THERMOSETTING RESIN
2007年
2期
19-22
,共4页
袁才登%段春华%许涌深%曹同玉
袁纔登%段春華%許湧深%曹同玉
원재등%단춘화%허용심%조동옥
环氧树脂%丙烯酸%乙酰丙酮铬(Ⅲ)%过渡金属络合物%酯化反应
環氧樹脂%丙烯痠%乙酰丙酮鉻(Ⅲ)%過渡金屬絡閤物%酯化反應
배양수지%병희산%을선병동락(Ⅲ)%과도금속락합물%지화반응
采用乙酰丙酮和三氯化铬制备乙酰丙酮铬(Ⅲ)络合物,主要讨论pH值对产物产率的影响.通过连续滴加碱溶液的方式控制体系pH值于7.0左右,可使络合物产率达到70%以上.并以有机铬络合物作为催化剂催化环氧树脂与丙烯酸的酯化反应,研究了催化剂用量及温度等对反应速率的影响,对酯化产物进行了红外光谱表征.结果表明,乙酰丙酮铬(Ⅲ)是一种有效的催化剂,当其用量为环氧树脂和丙烯酸用量的0.1%~0.2%,在110~120℃反应1.5~2.5h,在较短时间内可达到较高的转化率.经红外光谱测试和计算,环氧基转化率约为48.56%,与理论值基本一致.
採用乙酰丙酮和三氯化鉻製備乙酰丙酮鉻(Ⅲ)絡閤物,主要討論pH值對產物產率的影響.通過連續滴加堿溶液的方式控製體繫pH值于7.0左右,可使絡閤物產率達到70%以上.併以有機鉻絡閤物作為催化劑催化環氧樹脂與丙烯痠的酯化反應,研究瞭催化劑用量及溫度等對反應速率的影響,對酯化產物進行瞭紅外光譜錶徵.結果錶明,乙酰丙酮鉻(Ⅲ)是一種有效的催化劑,噹其用量為環氧樹脂和丙烯痠用量的0.1%~0.2%,在110~120℃反應1.5~2.5h,在較短時間內可達到較高的轉化率.經紅外光譜測試和計算,環氧基轉化率約為48.56%,與理論值基本一緻.
채용을선병동화삼록화락제비을선병동락(Ⅲ)락합물,주요토론pH치대산물산솔적영향.통과련속적가감용액적방식공제체계pH치우7.0좌우,가사락합물산솔체도70%이상.병이유궤락락합물작위최화제최화배양수지여병희산적지화반응,연구료최화제용량급온도등대반응속솔적영향,대지화산물진행료홍외광보표정.결과표명,을선병동락(Ⅲ)시일충유효적최화제,당기용량위배양수지화병희산용량적0.1%~0.2%,재110~120℃반응1.5~2.5h,재교단시간내가체도교고적전화솔.경홍외광보측시화계산,배양기전화솔약위48.56%,여이론치기본일치.