合成橡胶工业
閤成橡膠工業
합성상효공업
CHINA SYNTHETIC RUBBER INDUSTRY
2010年
2期
139-141
,共3页
胡少坤%胡开放%潘广勤%于晶%陈继明
鬍少坤%鬍開放%潘廣勤%于晶%陳繼明
호소곤%호개방%반엄근%우정%진계명
端羟基液体丁腈橡胶%环氧树脂%预聚体%改性%拉伸强度%剪切强度%磨蚀
耑羥基液體丁腈橡膠%環氧樹脂%預聚體%改性%拉伸彊度%剪切彊度%磨蝕
단간기액체정정상효%배양수지%예취체%개성%랍신강도%전절강도%마식
hydroxy-terminated liquid nitrile rubber%epoxy resin%pre-polymer%modification%tensile strength%shear strength%abrasion
用端羟基液体丁腈橡胶(HTLN)与2,4-甲苯二异氰酸酯进行反应得到HTLN预聚体,用其对环氧树脂进行化学改性,得到HTLN改性环氧树脂;考察了HTLN用量对改性环氧树脂微观形貌、拉伸强度和剪切强度的影响及改性环氧树脂的抗磨蚀性能.结果表明,随着HTLN预聚体用量的增加,改性环氧树脂的拉伸强度、剪切强度先升高后降低,在其质量分数为30%时,拉伸强度和剪切强度达到最高;在施加的负荷和HTLN用量一定的情况下,改性环氧树脂的磨蚀随滑动速率的增加而明显增加.#
用耑羥基液體丁腈橡膠(HTLN)與2,4-甲苯二異氰痠酯進行反應得到HTLN預聚體,用其對環氧樹脂進行化學改性,得到HTLN改性環氧樹脂;攷察瞭HTLN用量對改性環氧樹脂微觀形貌、拉伸彊度和剪切彊度的影響及改性環氧樹脂的抗磨蝕性能.結果錶明,隨著HTLN預聚體用量的增加,改性環氧樹脂的拉伸彊度、剪切彊度先升高後降低,在其質量分數為30%時,拉伸彊度和剪切彊度達到最高;在施加的負荷和HTLN用量一定的情況下,改性環氧樹脂的磨蝕隨滑動速率的增加而明顯增加.#
용단간기액체정정상효(HTLN)여2,4-갑분이이청산지진행반응득도HTLN예취체,용기대배양수지진행화학개성,득도HTLN개성배양수지;고찰료HTLN용량대개성배양수지미관형모、랍신강도화전절강도적영향급개성배양수지적항마식성능.결과표명,수착HTLN예취체용량적증가,개성배양수지적랍신강도、전절강도선승고후강저,재기질량분수위30%시,랍신강도화전절강도체도최고;재시가적부하화HTLN용량일정적정황하,개성배양수지적마식수활동속솔적증가이명현증가.#
Pre-polymer was synthesized by hydroxy-terminated liquid nitrile rubber(HTLN) reacted with 2,4-tolylene diisocyanate, and epoxy resin was modified with the HTLN pre-polymer. The effect of amount of HTLN on morphology, tensile strength and shear strength of the modified epoxy resin, as well as abrasion resistance of the modified epoxy resin were investigated. The results showed that the tensile strength and shear strength of the modified epoxy resin increased first and then decreased with increasing amount of the HTLN pre-polymer. When the mass fraction of the HTLN pre-polymer was 30%, the tensile strength and shear strength of the modified epoxy resin were the best. The abrasion of the modified epoxy resin increased with increasing sliding rate at fixed amounts of applied load and HTLN.