粉末冶金技术
粉末冶金技術
분말야금기술
POWDER METALLURGY TECHNOLOGY
2010年
1期
58-60
,共3页
碳化硅陶瓷%烧结温度%显微结构%力学性能
碳化硅陶瓷%燒結溫度%顯微結構%力學性能
탄화규도자%소결온도%현미결구%역학성능
silicon carbide ceramics%sintering temperature%microstructure%mechanical property
采用硼、碳助剂无压烧结制备碳化硅陶瓷.针对烧结温度与碳化硅烧结体密度、抗弯强度以及硬度之间的关系进行了试验研究,并对不同温度下制备的烧结体进行了显微结构形貌观察和XRD图谱分析.结果表明,烧结温度在2190~2220℃范围内可以制备密度高、力学性能好的碳化硅陶瓷.其相对密度超过96%;抗弯强度接近400MPa;维氏硬度23GPa以上.在试验温度范围内,密度与抗弯强度之间的关系近似为线性关系,密度越高抗弯强度和硬度性能越好.
採用硼、碳助劑無壓燒結製備碳化硅陶瓷.針對燒結溫度與碳化硅燒結體密度、抗彎彊度以及硬度之間的關繫進行瞭試驗研究,併對不同溫度下製備的燒結體進行瞭顯微結構形貌觀察和XRD圖譜分析.結果錶明,燒結溫度在2190~2220℃範圍內可以製備密度高、力學性能好的碳化硅陶瓷.其相對密度超過96%;抗彎彊度接近400MPa;維氏硬度23GPa以上.在試驗溫度範圍內,密度與抗彎彊度之間的關繫近似為線性關繫,密度越高抗彎彊度和硬度性能越好.
채용붕、탄조제무압소결제비탄화규도자.침대소결온도여탄화규소결체밀도、항만강도이급경도지간적관계진행료시험연구,병대불동온도하제비적소결체진행료현미결구형모관찰화XRD도보분석.결과표명,소결온도재2190~2220℃범위내가이제비밀도고、역학성능호적탄화규도자.기상대밀도초과96%;항만강도접근400MPa;유씨경도23GPa이상.재시험온도범위내,밀도여항만강도지간적관계근사위선성관계,밀도월고항만강도화경도성능월호.
Pressureless sintering of silicon carbide with C、B as sintering additives were carried out. The influence of sintering temperature on mechanical properties of silicon carbide ceramics was investigated. Microstructure and XRD pattern of the sintered bodies at different sintering temperature were analyzed. The results show that dense SiC ceramics with good mechanical properties are obtained at sintering temperature of 2190~2220℃. It has relative density of more than 96%;bending strength of near 400MPa; Vickers hardness of more than 23GPa. In the testing temperature range, the relation curve between density and bending strength is approximate to linear one. The higher density, the better is the bending strength and the hardness.