热加工工艺
熱加工工藝
열가공공예
HOT WORKING TECHNOLOGY
2010年
3期
1-4,9
,共5页
赵惠%李平仓%薛治国%黄张洪%王虎年
趙惠%李平倉%薛治國%黃張洪%王虎年
조혜%리평창%설치국%황장홍%왕호년
爆炸复合%钛/钢复合板%运动位移模拟
爆炸複閤%鈦/鋼複閤闆%運動位移模擬
폭작복합%태/강복합판%운동위이모의
explosive welding%Ti/Steel cladded plate%numerical simulation for displacement
采用非线性动力有限元法建立了复合板在爆炸焊接过程中的有限元计算模型,对复合板运动状态进行了模拟和分析.利用有限元软件的网格划分功能建立了5/41mill×3850min×6650mm钛/钢复合板模型,实现了对复板运动过程的三维有限元模拟.实验研究了不同间隙条件下复板运动过程的位移云图,并通过对实验结果进行比较与分析后,确定当间隙高度为8min时,爆炸焊接后复板上各点的最终位移都达到了8mm,复合板结合率为100%.该研究为大面积钛钢复合板的爆炸焊接工艺参数的制定提供了依据.
採用非線性動力有限元法建立瞭複閤闆在爆炸銲接過程中的有限元計算模型,對複閤闆運動狀態進行瞭模擬和分析.利用有限元軟件的網格劃分功能建立瞭5/41mill×3850min×6650mm鈦/鋼複閤闆模型,實現瞭對複闆運動過程的三維有限元模擬.實驗研究瞭不同間隙條件下複闆運動過程的位移雲圖,併通過對實驗結果進行比較與分析後,確定噹間隙高度為8min時,爆炸銲接後複闆上各點的最終位移都達到瞭8mm,複閤闆結閤率為100%.該研究為大麵積鈦鋼複閤闆的爆炸銲接工藝參數的製定提供瞭依據.
채용비선성동력유한원법건립료복합판재폭작한접과정중적유한원계산모형,대복합판운동상태진행료모의화분석.이용유한원연건적망격화분공능건립료5/41mill×3850min×6650mm태/강복합판모형,실현료대복판운동과정적삼유유한원모의.실험연구료불동간극조건하복판운동과정적위이운도,병통과대실험결과진행비교여분석후,학정당간극고도위8min시,폭작한접후복판상각점적최종위이도체도료8mm,복합판결합솔위100%.해연구위대면적태강복합판적폭작한접공예삼수적제정제공료의거.
Finite element software was used to simulate displacement of Ti/Steel cladded plate during explosive welding.The model of Ti/Steel cladded plate(5/41mm×3850 mm×6650mm)was founded by gnds dividing.Displacements contour bands of Ti plates were investigated under different spacers,and pass rate of cladded plate reached 100%when spacer Was 8 mm.This study provides a basis for explosive welding oflarge size Ti/Steel eladded plate.