中国表面工程
中國錶麵工程
중국표면공정
CHINA SURFACE ENGINEERING
2012年
2期
63-68
,共6页
吴宏观%蔡航伟%马志康%王成磊%李冰%高原
吳宏觀%蔡航偉%馬誌康%王成磊%李冰%高原
오굉관%채항위%마지강%왕성뢰%리빙%고원
钨钼钇共渗%钨钼钇共渗强化层%回火硬度%红硬性
鎢鉬釔共滲%鎢鉬釔共滲彊化層%迴火硬度%紅硬性
오목을공삼%오목을공삼강화층%회화경도%홍경성
利用双层辉光等离子渗金属技术,在Q235钢表面分别进行钨钼钇共渗与钨钼共渗,形成均匀致密合金扩散层;共渗后,将两种试样分别在960℃、980℃、1020℃下进行8h渗碳及淬火,并在200℃低温回火lh.之后将两者在1 020℃渗碳及淬火,并分别进行200~700℃回火.采用显微硬度仪检测其表面硬度,采用光学显微镜、SEM及EDS分别对渗层进行金相组织及成分分析.结果表明:其回火特征与冶金高速钢类似,在500℃时出现“二次硬化”现象,回火硬度达到峰值,且前者高于后者.将经过1 020℃渗碳淬火后的两种试样在600℃下保温1h后空冷,重复4次后,前者与后者的表面硬度最大值分别达到750 HV0.05、650 HV0.05.
利用雙層輝光等離子滲金屬技術,在Q235鋼錶麵分彆進行鎢鉬釔共滲與鎢鉬共滲,形成均勻緻密閤金擴散層;共滲後,將兩種試樣分彆在960℃、980℃、1020℃下進行8h滲碳及淬火,併在200℃低溫迴火lh.之後將兩者在1 020℃滲碳及淬火,併分彆進行200~700℃迴火.採用顯微硬度儀檢測其錶麵硬度,採用光學顯微鏡、SEM及EDS分彆對滲層進行金相組織及成分分析.結果錶明:其迴火特徵與冶金高速鋼類似,在500℃時齣現“二次硬化”現象,迴火硬度達到峰值,且前者高于後者.將經過1 020℃滲碳淬火後的兩種試樣在600℃下保溫1h後空冷,重複4次後,前者與後者的錶麵硬度最大值分彆達到750 HV0.05、650 HV0.05.
이용쌍층휘광등리자삼금속기술,재Q235강표면분별진행오목을공삼여오목공삼,형성균균치밀합금확산층;공삼후,장량충시양분별재960℃、980℃、1020℃하진행8h삼탄급쉬화,병재200℃저온회화lh.지후장량자재1 020℃삼탄급쉬화,병분별진행200~700℃회화.채용현미경도의검측기표면경도,채용광학현미경、SEM급EDS분별대삼층진행금상조직급성분분석.결과표명:기회화특정여야금고속강유사,재500℃시출현“이차경화”현상,회화경도체도봉치,차전자고우후자.장경과1 020℃삼탄쉬화후적량충시양재600℃하보온1h후공랭,중복4차후,전자여후자적표면경도최대치분별체도750 HV0.05、650 HV0.05.