中国表面工程
中國錶麵工程
중국표면공정
CHINA SURFACE ENGINEERING
2001年
1期
24-26,30
,共4页
辛钢%高阳%黑祖昆%颜永根%陆明和
辛鋼%高暘%黑祖昆%顏永根%陸明和
신강%고양%흑조곤%안영근%륙명화
气体爆燃喷涂%铁铝涂层%微观结构
氣體爆燃噴塗%鐵鋁塗層%微觀結構
기체폭연분도%철려도층%미관결구
采用不同的喷涂工艺参数,分别在45钢基体上制备了电弧喷涂铁铝涂层,采用电子探针(EPMA)、X射线衍射(XRD)、光学显微镜和显微硬度计等仪器研究了气体爆燃铁铝涂层的表面形貌、显微硬度、涂层的成分和相结构,结果表明,喷涂工艺的改变明显影响喷涂层的相组成,随着单位时间内提供给粉末能量的减少,得到黑白相间的片层状结构,黑色相是Fe4Al13,白色相是FeAl;增加单位时间内提供给粉末的能量,可以得到均匀的微观组织,成分为FeAl。
採用不同的噴塗工藝參數,分彆在45鋼基體上製備瞭電弧噴塗鐵鋁塗層,採用電子探針(EPMA)、X射線衍射(XRD)、光學顯微鏡和顯微硬度計等儀器研究瞭氣體爆燃鐵鋁塗層的錶麵形貌、顯微硬度、塗層的成分和相結構,結果錶明,噴塗工藝的改變明顯影響噴塗層的相組成,隨著單位時間內提供給粉末能量的減少,得到黑白相間的片層狀結構,黑色相是Fe4Al13,白色相是FeAl;增加單位時間內提供給粉末的能量,可以得到均勻的微觀組織,成分為FeAl。
채용불동적분도공예삼수,분별재45강기체상제비료전호분도철려도층,채용전자탐침(EPMA)、X사선연사(XRD)、광학현미경화현미경도계등의기연구료기체폭연철려도층적표면형모、현미경도、도층적성분화상결구,결과표명,분도공예적개변명현영향분도층적상조성,수착단위시간내제공급분말능량적감소,득도흑백상간적편층상결구,흑색상시Fe4Al13,백색상시FeAl;증가단위시간내제공급분말적능량,가이득도균균적미관조직,성분위FeAl。
Microstructure and phases of Fe-A1binary alloy coating sprayed on 1045 steel sheet bythe detonation spraying with different process parameters were investigated by metallography,electron probe and x-ray diffraction (XRD) methods.The results of analyses showed that the compositionof the coating, which included Fe-A1, Fe4Al13 and afew A12O3 phases, was different from the pristinepowder of Fe4Al13. The content of FeA1 decreasedwith the rising of the proportion of oxygen andacetylene and the decreasing of frequency of thegun firing. Micro-hardness tests indicated that itchanged inhomogeneously with the variation ofcontent of FeAl lamellar structure.