河北科技大学学报
河北科技大學學報
하북과기대학학보
JOURNAL OF THE HEBEI UNIVERSITY OF SCIENCE AND ECHNOLOGY
2004年
2期
65-68
,共4页
WC%喷熔工艺%低应力磨粒磨损%冲击磨粒磨损
WC%噴鎔工藝%低應力磨粒磨損%遲擊磨粒磨損
WC%분용공예%저응력마립마손%충격마립마손
在自熔性合金粉末Ni60中机械混合不同质量分数的WC进行火焰喷熔,通过喷熔工艺性能试验、喷熔层宏观硬度测试、喷熔层低应力磨粒磨损试验、喷熔层冲击磨粒磨损试验和显微组织分析,研究了w(WC)对喷焊层耐磨性能的影响.试验证明:随着合金粉中w(WC)的增大,喷焊工艺性能变差,但当w(WC)低于50%时,WC的加入对喷焊工艺性能影响不很明显,喷熔层硬度变化不大,喷熔层低应力磨粒磨损性能随w(WC)的增大而提高;当w(WC)大于50%时,WC的加入使喷熔工艺性能变得极差,喷熔层的硬度和耐低应力磨粒磨损性能降低.由于WC硬而脆的性能和在喷熔层显微组织中起分割基体的作用,喷熔层耐冲击磨粒磨损性能随w(WC)的增大而降低.
在自鎔性閤金粉末Ni60中機械混閤不同質量分數的WC進行火燄噴鎔,通過噴鎔工藝性能試驗、噴鎔層宏觀硬度測試、噴鎔層低應力磨粒磨損試驗、噴鎔層遲擊磨粒磨損試驗和顯微組織分析,研究瞭w(WC)對噴銲層耐磨性能的影響.試驗證明:隨著閤金粉中w(WC)的增大,噴銲工藝性能變差,但噹w(WC)低于50%時,WC的加入對噴銲工藝性能影響不很明顯,噴鎔層硬度變化不大,噴鎔層低應力磨粒磨損性能隨w(WC)的增大而提高;噹w(WC)大于50%時,WC的加入使噴鎔工藝性能變得極差,噴鎔層的硬度和耐低應力磨粒磨損性能降低.由于WC硬而脆的性能和在噴鎔層顯微組織中起分割基體的作用,噴鎔層耐遲擊磨粒磨損性能隨w(WC)的增大而降低.
재자용성합금분말Ni60중궤계혼합불동질량분수적WC진행화염분용,통과분용공예성능시험、분용층굉관경도측시、분용층저응력마립마손시험、분용층충격마립마손시험화현미조직분석,연구료w(WC)대분한층내마성능적영향.시험증명:수착합금분중w(WC)적증대,분한공예성능변차,단당w(WC)저우50%시,WC적가입대분한공예성능영향불흔명현,분용층경도변화불대,분용층저응력마립마손성능수w(WC)적증대이제고;당w(WC)대우50%시,WC적가입사분용공예성능변득겁차,분용층적경도화내저응력마립마손성능강저.유우WC경이취적성능화재분용층현미조직중기분할기체적작용,분용층내충격마립마손성능수w(WC)적증대이강저.