焊接学报
銲接學報
한접학보
TRANSACTIONS OF THE CHINA WELDING INSTITUTION
2006年
5期
85-88
,共4页
赵文庆%吴爱萍%邹贵生%刘根茂
趙文慶%吳愛萍%鄒貴生%劉根茂
조문경%오애평%추귀생%류근무
高纯氧化铝陶瓷%钛%钎焊%接头组织%接头抗剪强度
高純氧化鋁陶瓷%鈦%釬銲%接頭組織%接頭抗剪彊度
고순양화려도자%태%천한%접두조직%접두항전강도
电真空应用中,要求高纯氧化铝与金属钛的连接接头不仅要有较好的强度,还要有高的气密性.用Ag-Cu-Ti钎料钎焊高纯氧化铝陶瓷与金属钛,钎焊温度为825~875℃,保温时间为15~20min,陶瓷表面为烧结自然表面时,钎焊接头抗剪强度可达到100MPa以上,连接温度过低或过高,保温时间过短或过长均对接头强度不利.陶瓷表面研磨后,接头强度降低.钎料厚度在60μm或105μm对接头强度的影响不大.接头由Al2O3/反应层(Cu,Al,Ti,0)/Ag+Cu-Ti化合物/α-Ti(Cu)/Ti构成.反应层主要以Cu3Ti3O和Cu4Ti为主.
電真空應用中,要求高純氧化鋁與金屬鈦的連接接頭不僅要有較好的彊度,還要有高的氣密性.用Ag-Cu-Ti釬料釬銲高純氧化鋁陶瓷與金屬鈦,釬銲溫度為825~875℃,保溫時間為15~20min,陶瓷錶麵為燒結自然錶麵時,釬銲接頭抗剪彊度可達到100MPa以上,連接溫度過低或過高,保溫時間過短或過長均對接頭彊度不利.陶瓷錶麵研磨後,接頭彊度降低.釬料厚度在60μm或105μm對接頭彊度的影響不大.接頭由Al2O3/反應層(Cu,Al,Ti,0)/Ag+Cu-Ti化閤物/α-Ti(Cu)/Ti構成.反應層主要以Cu3Ti3O和Cu4Ti為主.
전진공응용중,요구고순양화려여금속태적련접접두불부요유교호적강도,환요유고적기밀성.용Ag-Cu-Ti천료천한고순양화려도자여금속태,천한온도위825~875℃,보온시간위15~20min,도자표면위소결자연표면시,천한접두항전강도가체도100MPa이상,련접온도과저혹과고,보온시간과단혹과장균대접두강도불리.도자표면연마후,접두강도강저.천료후도재60μm혹105μm대접두강도적영향불대.접두유Al2O3/반응층(Cu,Al,Ti,0)/Ag+Cu-Ti화합물/α-Ti(Cu)/Ti구성.반응층주요이Cu3Ti3O화Cu4Ti위주.