材料导报
材料導報
재료도보
MATERIALS REVIEW
2009年
z1期
35-37,40
,共4页
刘思思%周虹峰%周锦鑫%顾顺超
劉思思%週虹峰%週錦鑫%顧順超
류사사%주홍봉%주금흠%고순초
悬浮聚合%多孔微球%粒径分布%孔比表面积
懸浮聚閤%多孔微毬%粒徑分佈%孔比錶麵積
현부취합%다공미구%립경분포%공비표면적
suspension polymerization%porous micro-spheres%distribution of particles%pore surface area
以苯乙烯、二乙烯苯为单体,引入混合溶剂作为致孔剂,采用悬浮聚合的方法制备了多孔交联聚苯乙烯微球,并通过有机萃取等方法带出致孔剂,形成永久性大孔.分析了搅拌速度、分散剂用量、致孔剂等因素对微球粒径分布和孔比表面积的影响,研究了不同工艺条件下的微球形态.结果表明,转速在180r/min左右,分散剂质量分数在0.15%左右时,可以制得粒径范围为0.2~0.8mm的聚苯乙烯微球,且微球具有良好的粒径分布.采用石蜡/甲苯、石蜡/乙酸乙酯为致孔剂时,可以形成纳米级小孔,且当石蜡/甲苯用量为86%时,孔比表面积可达到33.07m2/g,并随着交联剂用量的增加而增大.
以苯乙烯、二乙烯苯為單體,引入混閤溶劑作為緻孔劑,採用懸浮聚閤的方法製備瞭多孔交聯聚苯乙烯微毬,併通過有機萃取等方法帶齣緻孔劑,形成永久性大孔.分析瞭攪拌速度、分散劑用量、緻孔劑等因素對微毬粒徑分佈和孔比錶麵積的影響,研究瞭不同工藝條件下的微毬形態.結果錶明,轉速在180r/min左右,分散劑質量分數在0.15%左右時,可以製得粒徑範圍為0.2~0.8mm的聚苯乙烯微毬,且微毬具有良好的粒徑分佈.採用石蠟/甲苯、石蠟/乙痠乙酯為緻孔劑時,可以形成納米級小孔,且噹石蠟/甲苯用量為86%時,孔比錶麵積可達到33.07m2/g,併隨著交聯劑用量的增加而增大.
이분을희、이을희분위단체,인입혼합용제작위치공제,채용현부취합적방법제비료다공교련취분을희미구,병통과유궤췌취등방법대출치공제,형성영구성대공.분석료교반속도、분산제용량、치공제등인소대미구립경분포화공비표면적적영향,연구료불동공예조건하적미구형태.결과표명,전속재180r/min좌우,분산제질량분수재0.15%좌우시,가이제득립경범위위0.2~0.8mm적취분을희미구,차미구구유량호적립경분포.채용석사/갑분、석사/을산을지위치공제시,가이형성납미급소공,차당석사/갑분용량위86%시,공비표면적가체도33.07m2/g,병수착교련제용량적증가이증대.
Porous cross-linked poly(styrene-divinylbenzene)micro-spheres are synthesized by traditional suspension polymerization with mixed solvent as pore-forming agent,which will be carried out by organic extraction.Many factors affect the distribution of particles and the pore surface area,such as agitation speed,concentration of dispersant,pore-forming agent and so on,are focused on analysis.It can be concluded that the PS particles whose diameter are in the range of 0.2~0.8mm can be prepared,when the rotate speed is around 180r/min,and the concentration of dispersant is about 0.15%.Besides,the distribution of particles is also favorable.When paraffin/toluene,paraffin/ethyl acetate are as pore-forming agent,the pores of the particles are nano-sized,and the pore surface areas can be up to 33.07m2/g,which increase with the amount of crosslinker increasing.