特种铸造及有色合金
特種鑄造及有色閤金
특충주조급유색합금
SPECIAL CASTING & NONFERROUS ALLOYS
2010年
5期
393-395
,共3页
毛卫民%朱达平%张佳宾%姚景文
毛衛民%硃達平%張佳賓%姚景文
모위민%주체평%장가빈%요경문
半固态%浇注温度%电磁搅拌%ZL201A铝合金%显微组织
半固態%澆註溫度%電磁攪拌%ZL201A鋁閤金%顯微組織
반고태%요주온도%전자교반%ZL201A려합금%현미조직
利用低过热度浇注和弱电磁搅拌方法制备了半固态ZL201A铝合金浆料,浇注温度分别为678、663、648 ℃,利用光学显微镜观察了不同条件下的浆料组织.试验结果表明,随着浇注温度的降低,半固态ZL201A铝合金浆料内部组织中的初生α-Al由蔷薇状向球状转变,晶粒尺寸逐渐变小,分布更均匀.同时,浆料边缘和底部组织中的初生α-Al的形貌由粗大的枝晶向蔷薇状转变.对于半固态ZL201A铝合金浆料的制备,较佳的浇注温度为663 ℃.电磁搅拌均匀了ZL201A铝合金液的温度场,加大了同时凝固的区域,细化了初生α-Al晶粒;同时结晶潜热的集中释放有助于蔷薇状初生α-Al的根部熔断,加速了球状初生α-Al的形成.
利用低過熱度澆註和弱電磁攪拌方法製備瞭半固態ZL201A鋁閤金漿料,澆註溫度分彆為678、663、648 ℃,利用光學顯微鏡觀察瞭不同條件下的漿料組織.試驗結果錶明,隨著澆註溫度的降低,半固態ZL201A鋁閤金漿料內部組織中的初生α-Al由薔薇狀嚮毬狀轉變,晶粒呎吋逐漸變小,分佈更均勻.同時,漿料邊緣和底部組織中的初生α-Al的形貌由粗大的枝晶嚮薔薇狀轉變.對于半固態ZL201A鋁閤金漿料的製備,較佳的澆註溫度為663 ℃.電磁攪拌均勻瞭ZL201A鋁閤金液的溫度場,加大瞭同時凝固的區域,細化瞭初生α-Al晶粒;同時結晶潛熱的集中釋放有助于薔薇狀初生α-Al的根部鎔斷,加速瞭毬狀初生α-Al的形成.
이용저과열도요주화약전자교반방법제비료반고태ZL201A려합금장료,요주온도분별위678、663、648 ℃,이용광학현미경관찰료불동조건하적장료조직.시험결과표명,수착요주온도적강저,반고태ZL201A려합금장료내부조직중적초생α-Al유장미상향구상전변,정립척촌축점변소,분포경균균.동시,장료변연화저부조직중적초생α-Al적형모유조대적지정향장미상전변.대우반고태ZL201A려합금장료적제비,교가적요주온도위663 ℃.전자교반균균료ZL201A려합금액적온도장,가대료동시응고적구역,세화료초생α-Al정립;동시결정잠열적집중석방유조우장미상초생α-Al적근부용단,가속료구상초생α-Al적형성.