电瓷避雷器
電瓷避雷器
전자피뢰기
INSULATORS AND SURGE ARRESTERS
2006年
1期
7-11
,共5页
棒形悬式%芯棒%金属附件%连接区%强度配合%破坏负荷
棒形懸式%芯棒%金屬附件%連接區%彊度配閤%破壞負荷
봉형현식%심봉%금속부건%련접구%강도배합%파배부하
介绍了国内外棒形悬式复合绝缘子金属附件连接区的设计结构,从不同厂家芯棒、压接力和生产工序三方面研究了连接区采用压接式结构对产品机械性能的影响,提出了在设计连接区时应考虑圆度、连接区的长度、端口的密封性、压块的长度及壁厚等因素.通过试验,认为压力小,易抽芯;压力大,易损伤芯棒.进行二段硫化后,强度降低了约20%,经原压力补压后,连接区强度可恢复,强度配合合理.推荐70kN级压力值可控制在(12.5~13.0)MPa,100kN级压力值可控制在(20.0~20.5)MPa以及160 kN级压力值可控制在17.5MPa,压两次,保压时间均为6s.
介紹瞭國內外棒形懸式複閤絕緣子金屬附件連接區的設計結構,從不同廠傢芯棒、壓接力和生產工序三方麵研究瞭連接區採用壓接式結構對產品機械性能的影響,提齣瞭在設計連接區時應攷慮圓度、連接區的長度、耑口的密封性、壓塊的長度及壁厚等因素.通過試驗,認為壓力小,易抽芯;壓力大,易損傷芯棒.進行二段硫化後,彊度降低瞭約20%,經原壓力補壓後,連接區彊度可恢複,彊度配閤閤理.推薦70kN級壓力值可控製在(12.5~13.0)MPa,100kN級壓力值可控製在(20.0~20.5)MPa以及160 kN級壓力值可控製在17.5MPa,壓兩次,保壓時間均為6s.
개소료국내외봉형현식복합절연자금속부건련접구적설계결구,종불동엄가심봉、압접력화생산공서삼방면연구료련접구채용압접식결구대산품궤계성능적영향,제출료재설계련접구시응고필원도、련접구적장도、단구적밀봉성、압괴적장도급벽후등인소.통과시험,인위압력소,역추심;압력대,역손상심봉.진행이단류화후,강도강저료약20%,경원압력보압후,련접구강도가회복,강도배합합리.추천70kN급압력치가공제재(12.5~13.0)MPa,100kN급압력치가공제재(20.0~20.5)MPa이급160 kN급압력치가공제재17.5MPa,압량차,보압시간균위6s.