动力工程
動力工程
동력공정
POWER ENGINEERING
2006年
6期
908-912
,共5页
刘少光%吴进明%张升才%胡小海%荣淑杰%李志章
劉少光%吳進明%張升纔%鬍小海%榮淑傑%李誌章
류소광%오진명%장승재%호소해%영숙걸%리지장
材料科学%锅炉管道%耐磨涂层%高温冲蚀磨损%抗氧化性能
材料科學%鍋爐管道%耐磨塗層%高溫遲蝕磨損%抗氧化性能
재료과학%과로관도%내마도층%고온충식마손%항양화성능
开发两种适用于超临界锅炉管道防磨的含TiAl3(AW1)、Cr3C2(AW2)的复合粉芯丝材,采用超音速电弧喷涂技术制取耐磨涂层,结合光学显微镜、维氏硬度、X射线衍射、场发射扫描电子显微镜、能谱分析等分析方法对喷涂层的的微观组织结构和高温冲蚀磨损规律进行研究,并与20钢进行对比分析.结果表明:AW1、AW2涂层具有固溶体相和氧化物相相互间隔的叠层结构特点;经800℃、150 h氧化试验,AW1和AW2涂层的抗氧化性能分别是20钢的10倍和15倍;20钢、AW1和AW2涂层的最大冲蚀率分别出现在15°和45°冲蚀角附近;AW1涂层具有与商用AW2涂层接近的耐高温冲蚀性能,耐冲蚀性能明显优于20钢;当冲蚀角为45°时,AW1和AW2涂层的耐冲蚀性分别是20钢的3.1和3.0倍.图7表2参6
開髮兩種適用于超臨界鍋爐管道防磨的含TiAl3(AW1)、Cr3C2(AW2)的複閤粉芯絲材,採用超音速電弧噴塗技術製取耐磨塗層,結閤光學顯微鏡、維氏硬度、X射線衍射、場髮射掃描電子顯微鏡、能譜分析等分析方法對噴塗層的的微觀組織結構和高溫遲蝕磨損規律進行研究,併與20鋼進行對比分析.結果錶明:AW1、AW2塗層具有固溶體相和氧化物相相互間隔的疊層結構特點;經800℃、150 h氧化試驗,AW1和AW2塗層的抗氧化性能分彆是20鋼的10倍和15倍;20鋼、AW1和AW2塗層的最大遲蝕率分彆齣現在15°和45°遲蝕角附近;AW1塗層具有與商用AW2塗層接近的耐高溫遲蝕性能,耐遲蝕性能明顯優于20鋼;噹遲蝕角為45°時,AW1和AW2塗層的耐遲蝕性分彆是20鋼的3.1和3.0倍.圖7錶2參6
개발량충괄용우초림계과로관도방마적함TiAl3(AW1)、Cr3C2(AW2)적복합분심사재,채용초음속전호분도기술제취내마도층,결합광학현미경、유씨경도、X사선연사、장발사소묘전자현미경、능보분석등분석방법대분도층적적미관조직결구화고온충식마손규률진행연구,병여20강진행대비분석.결과표명:AW1、AW2도층구유고용체상화양화물상상호간격적첩층결구특점;경800℃、150 h양화시험,AW1화AW2도층적항양화성능분별시20강적10배화15배;20강、AW1화AW2도층적최대충식솔분별출현재15°화45°충식각부근;AW1도층구유여상용AW2도층접근적내고온충식성능,내충식성능명현우우20강;당충식각위45°시,AW1화AW2도층적내충식성분별시20강적3.1화3.0배.도7표2삼6