金属制品
金屬製品
금속제품
STEEL WIRE PRODUCTS
2011年
5期
56-58,63
,共4页
张全刚%邓保全%韩建伟%翟林甫%邹文辉
張全剛%鄧保全%韓建偉%翟林甫%鄒文輝
장전강%산보전%한건위%적림보%추문휘
H11Mn2SiA%气保焊丝%化学成分%金相组织%力学性能
H11Mn2SiA%氣保銲絲%化學成分%金相組織%力學性能
H11Mn2SiA%기보한사%화학성분%금상조직%역학성능
分析气保焊丝用H11Mn2SiA热轧盘条中合金元素对焊接性能的影响,设计盘条的化学成分和生产工艺流程,在Gleeble - 1500热模拟机上测定H11Mn2SiA动态CCT曲线.对比盘条在870,850,820℃吐丝温度下的金相组织和力学性能,结果表明,当盘条在斯太尔摩线冷却速度不大于1℃/s时,盘条能够完成平衡转变,且对盘条的金相组织和力学性能影响不大,铁素体晶粒度均为8.5级.分析不同碳质量分数对盘条力学性能的影响,结果表明,当碳质量分数不大于0.08%时能有效降低盘条抗拉强度.对碳质量分数为0.07%,吐丝温度870℃,冷速为0.51℃/s条件下生产的焊丝进行焊接试验评定,熔敷金属力学性能全部满足要求,抗拉强度540 MPa,-30℃平均V型冲击功67 J,焊接性能优良.
分析氣保銲絲用H11Mn2SiA熱軋盤條中閤金元素對銲接性能的影響,設計盤條的化學成分和生產工藝流程,在Gleeble - 1500熱模擬機上測定H11Mn2SiA動態CCT麯線.對比盤條在870,850,820℃吐絲溫度下的金相組織和力學性能,結果錶明,噹盤條在斯太爾摩線冷卻速度不大于1℃/s時,盤條能夠完成平衡轉變,且對盤條的金相組織和力學性能影響不大,鐵素體晶粒度均為8.5級.分析不同碳質量分數對盤條力學性能的影響,結果錶明,噹碳質量分數不大于0.08%時能有效降低盤條抗拉彊度.對碳質量分數為0.07%,吐絲溫度870℃,冷速為0.51℃/s條件下生產的銲絲進行銲接試驗評定,鎔敷金屬力學性能全部滿足要求,抗拉彊度540 MPa,-30℃平均V型遲擊功67 J,銲接性能優良.
분석기보한사용H11Mn2SiA열알반조중합금원소대한접성능적영향,설계반조적화학성분화생산공예류정,재Gleeble - 1500열모의궤상측정H11Mn2SiA동태CCT곡선.대비반조재870,850,820℃토사온도하적금상조직화역학성능,결과표명,당반조재사태이마선냉각속도불대우1℃/s시,반조능구완성평형전변,차대반조적금상조직화역학성능영향불대,철소체정립도균위8.5급.분석불동탄질량분수대반조역학성능적영향,결과표명,당탄질량분수불대우0.08%시능유효강저반조항랍강도.대탄질량분수위0.07%,토사온도870℃,랭속위0.51℃/s조건하생산적한사진행한접시험평정,용부금속역학성능전부만족요구,항랍강도540 MPa,-30℃평균V형충격공67 J,한접성능우량.