高电压技术
高電壓技術
고전압기술
HIGH VOLTAGE ENGINEERING
2006年
6期
60-63
,共4页
调制器%回扫充电%双线PFN%可控硅%设计
調製器%迴掃充電%雙線PFN%可控硅%設計
조제기%회소충전%쌍선PFN%가공규%설계
按某气象雷达对发射系统的具体要求,在满足磁控管正常工作条件的情况下,给出了调制器的技术指标,形成了调制器实现的功能框图,并介绍了其各个部分的原理和功能.调制器的设计采用3只串联可控硅作为放电开关(固态调制器);其最大工作电压可达3 kV,实际工作有40%的冗余,有利于提高调制器的可靠性;高压电源采用回扫充电方式的开关电源,它使充电、放电分时进行,可以抗调制器连通,减少电源纹波对调制器指标的影响;1μs矩形脉冲采用双线PFN形成,并给出了严格的理论分析,得到了可靠的调制器设计参数.双线PFN的充电电压和输出电压相等,在调制器输出电压相同的情况下,双线PFN的充电电压比单线PFN减小一半,可以有效地减少串联SCR的数量,给使用和维护带来了方便.调制器监控是通过PLC(Programed Logic Controller)编程实现的.PLC具有很强的抗干扰性能,并有标准的422串行接口,有利于外部连接.调制器对所有的故障信号和状态信号实时监控,把故障信号与加高压信号互锁,保证人、机安全.该调制器具有体积小、重量轻的特点,便于安装、使用.结果证明文中的逻辑分析和参数选择是合理的,满足工程设计要求.目前该调制器已在多部气象雷达发射机中应用,工作安全、可靠,对今后这方面的相关工程设计具有一定的借鉴作用.
按某氣象雷達對髮射繫統的具體要求,在滿足磁控管正常工作條件的情況下,給齣瞭調製器的技術指標,形成瞭調製器實現的功能框圖,併介紹瞭其各箇部分的原理和功能.調製器的設計採用3隻串聯可控硅作為放電開關(固態調製器);其最大工作電壓可達3 kV,實際工作有40%的冗餘,有利于提高調製器的可靠性;高壓電源採用迴掃充電方式的開關電源,它使充電、放電分時進行,可以抗調製器連通,減少電源紋波對調製器指標的影響;1μs矩形脈遲採用雙線PFN形成,併給齣瞭嚴格的理論分析,得到瞭可靠的調製器設計參數.雙線PFN的充電電壓和輸齣電壓相等,在調製器輸齣電壓相同的情況下,雙線PFN的充電電壓比單線PFN減小一半,可以有效地減少串聯SCR的數量,給使用和維護帶來瞭方便.調製器鑑控是通過PLC(Programed Logic Controller)編程實現的.PLC具有很彊的抗榦擾性能,併有標準的422串行接口,有利于外部連接.調製器對所有的故障信號和狀態信號實時鑑控,把故障信號與加高壓信號互鎖,保證人、機安全.該調製器具有體積小、重量輕的特點,便于安裝、使用.結果證明文中的邏輯分析和參數選擇是閤理的,滿足工程設計要求.目前該調製器已在多部氣象雷達髮射機中應用,工作安全、可靠,對今後這方麵的相關工程設計具有一定的藉鑒作用.
안모기상뢰체대발사계통적구체요구,재만족자공관정상공작조건적정황하,급출료조제기적기술지표,형성료조제기실현적공능광도,병개소료기각개부분적원리화공능.조제기적설계채용3지천련가공규작위방전개관(고태조제기);기최대공작전압가체3 kV,실제공작유40%적용여,유리우제고조제기적가고성;고압전원채용회소충전방식적개관전원,타사충전、방전분시진행,가이항조제기련통,감소전원문파대조제기지표적영향;1μs구형맥충채용쌍선PFN형성,병급출료엄격적이론분석,득도료가고적조제기설계삼수.쌍선PFN적충전전압화수출전압상등,재조제기수출전압상동적정황하,쌍선PFN적충전전압비단선PFN감소일반,가이유효지감소천련SCR적수량,급사용화유호대래료방편.조제기감공시통과PLC(Programed Logic Controller)편정실현적.PLC구유흔강적항간우성능,병유표준적422천행접구,유리우외부련접.조제기대소유적고장신호화상태신호실시감공,파고장신호여가고압신호호쇄,보증인、궤안전.해조제기구유체적소、중량경적특점,편우안장、사용.결과증명문중적라집분석화삼수선택시합리적,만족공정설계요구.목전해조제기이재다부기상뢰체발사궤중응용,공작안전、가고,대금후저방면적상관공정설계구유일정적차감작용.