兰州理工大学学报
蘭州理工大學學報
란주리공대학학보
JOURNAL OF LANZHOU UNIVERSITY OF TECHNOLOGY
2010年
6期
9-12
,共4页
喇培清%王鸿鼎%刘闪光%申达%刘雪梅%鞠倩
喇培清%王鴻鼎%劉閃光%申達%劉雪梅%鞠倩
나배청%왕홍정%류섬광%신체%류설매%국천
310S耐热钢%Al元素%高温压缩性能
310S耐熱鋼%Al元素%高溫壓縮性能
310S내열강%Al원소%고온압축성능
通过WS-4非自耗电弧炉熔炼制备Al质量分数2%~10%的耐热不锈钢310S,用Mef3光学金相显微镜和XRD研究其显微组织,采用Thermechastor-W热/力模拟试验机对所制备合金的高温压缩性能进行研究.结果表明,随着Al含量的增加,碳化物由网状转变为细小颗粒组成的不连续网状,最终转交为颗粒状,基体在含Al质量分数大干6%时由γ相转变为α相.不同Al含量的合金流变应力范围基本一致,合金的高温屈服强度由未添加Al元素时的74 MPa先降低至61 MPa后开始升高,在Al质量分数为6%时达到最大值86 MPa,之后高温屈服强度逐渐降低,加Al后合金热加工性能并未显著改善.
通過WS-4非自耗電弧爐鎔煉製備Al質量分數2%~10%的耐熱不鏽鋼310S,用Mef3光學金相顯微鏡和XRD研究其顯微組織,採用Thermechastor-W熱/力模擬試驗機對所製備閤金的高溫壓縮性能進行研究.結果錶明,隨著Al含量的增加,碳化物由網狀轉變為細小顆粒組成的不連續網狀,最終轉交為顆粒狀,基體在含Al質量分數大榦6%時由γ相轉變為α相.不同Al含量的閤金流變應力範圍基本一緻,閤金的高溫屈服彊度由未添加Al元素時的74 MPa先降低至61 MPa後開始升高,在Al質量分數為6%時達到最大值86 MPa,之後高溫屈服彊度逐漸降低,加Al後閤金熱加工性能併未顯著改善.
통과WS-4비자모전호로용련제비Al질량분수2%~10%적내열불수강310S,용Mef3광학금상현미경화XRD연구기현미조직,채용Thermechastor-W열/력모의시험궤대소제비합금적고온압축성능진행연구.결과표명,수착Al함량적증가,탄화물유망상전변위세소과립조성적불련속망상,최종전교위과립상,기체재함Al질량분수대간6%시유γ상전변위α상.불동Al함량적합금류변응력범위기본일치,합금적고온굴복강도유미첨가Al원소시적74 MPa선강저지61 MPa후개시승고,재Al질량분수위6%시체도최대치86 MPa,지후고온굴복강도축점강저,가Al후합금열가공성능병미현저개선.