材料工程
材料工程
재료공정
JOURNAL OF MATERIALS ENGINEERING
2007年
6期
50-54
,共5页
徐国忠%李贺军%白瑞成%陈拂晓%黄敏
徐國忠%李賀軍%白瑞成%陳拂曉%黃敏
서국충%리하군%백서성%진불효%황민
C/C复合材料%前驱体%ICVI%致密化
C/C複閤材料%前驅體%ICVI%緻密化
C/C복합재료%전구체%ICVI%치밀화
研究了分别以甲烷和丙烯为前驱体对制备C/C复合材料的新型ICVI工艺致密化速率及组织结构和力学性能的影响.考察了密度与致密化时间之间的变化规律和密度分布,采用偏光显微镜和扫描电镜观察材料的组织结构和试样的断口形貌,利用三点弯曲实验测定材料的弯曲强度.实验结果表明:在致密化时间100h前,以甲烷为前驱体,C/C复合材料的致密化速率比丙烯为前驱体时低,100h后致密化速率发生逆转;以甲烷为前驱体所得C/C复合材料的密度梯度小,组织结构为粗糙层,弯曲强度为250.87MPa,模量为29.29GPa;而以丙烯为前驱体所得C/C复合材料的密度梯度大,组织结构为光滑层,弯曲强度为102.75MPa,模量为11.42GPa.因此,相对而言甲烷作为制备C/C复合材料的前驱体优于丙烯.
研究瞭分彆以甲烷和丙烯為前驅體對製備C/C複閤材料的新型ICVI工藝緻密化速率及組織結構和力學性能的影響.攷察瞭密度與緻密化時間之間的變化規律和密度分佈,採用偏光顯微鏡和掃描電鏡觀察材料的組織結構和試樣的斷口形貌,利用三點彎麯實驗測定材料的彎麯彊度.實驗結果錶明:在緻密化時間100h前,以甲烷為前驅體,C/C複閤材料的緻密化速率比丙烯為前驅體時低,100h後緻密化速率髮生逆轉;以甲烷為前驅體所得C/C複閤材料的密度梯度小,組織結構為粗糙層,彎麯彊度為250.87MPa,模量為29.29GPa;而以丙烯為前驅體所得C/C複閤材料的密度梯度大,組織結構為光滑層,彎麯彊度為102.75MPa,模量為11.42GPa.因此,相對而言甲烷作為製備C/C複閤材料的前驅體優于丙烯.
연구료분별이갑완화병희위전구체대제비C/C복합재료적신형ICVI공예치밀화속솔급조직결구화역학성능적영향.고찰료밀도여치밀화시간지간적변화규률화밀도분포,채용편광현미경화소묘전경관찰재료적조직결구화시양적단구형모,이용삼점만곡실험측정재료적만곡강도.실험결과표명:재치밀화시간100h전,이갑완위전구체,C/C복합재료적치밀화속솔비병희위전구체시저,100h후치밀화속솔발생역전;이갑완위전구체소득C/C복합재료적밀도제도소,조직결구위조조층,만곡강도위250.87MPa,모량위29.29GPa;이이병희위전구체소득C/C복합재료적밀도제도대,조직결구위광활층,만곡강도위102.75MPa,모량위11.42GPa.인차,상대이언갑완작위제비C/C복합재료적전구체우우병희.