汽轮机技术
汽輪機技術
기륜궤기술
TURBINE TECHNOLOGY
2012年
2期
158-160,108
,共4页
崔亚辉%张俊杰%徐福海%毕春海%温武斌%陈荣轩
崔亞輝%張俊傑%徐福海%畢春海%溫武斌%陳榮軒
최아휘%장준걸%서복해%필춘해%온무빈%진영헌
汽轮机%振动故障诊断%汽流激振
汽輪機%振動故障診斷%汽流激振
기륜궤%진동고장진단%기류격진
某台300MW汽轮机的振动明显受到调门开启顺序和开度大小的影响,通过对机组的振动特征以及调门产生的汽流力进行分析、研究发现:采用调整阀门的开启顺序产生汽流力来提高轴承载荷并不能减小或消除该机组的振动,反而增大了机组的振动;原因是转子在汽缸中的径向位置发生了变化,改变了通流部分的间隙;通过采取合理的调门开启顺序和开度减小转子在汽缸中的偏移,虽然轴承偏心率减小、轴承载荷下降,但是振动水平明显降低了.由此可知,抑制汽流激振的方法有若干种,有些方法在现场实施起来可能会出现矛盾,此时首先需分析引起汽流激振的主要因素,然后采取能解决问题的关键措施,才能取得满意的效果.
某檯300MW汽輪機的振動明顯受到調門開啟順序和開度大小的影響,通過對機組的振動特徵以及調門產生的汽流力進行分析、研究髮現:採用調整閥門的開啟順序產生汽流力來提高軸承載荷併不能減小或消除該機組的振動,反而增大瞭機組的振動;原因是轉子在汽缸中的徑嚮位置髮生瞭變化,改變瞭通流部分的間隙;通過採取閤理的調門開啟順序和開度減小轉子在汽缸中的偏移,雖然軸承偏心率減小、軸承載荷下降,但是振動水平明顯降低瞭.由此可知,抑製汽流激振的方法有若榦種,有些方法在現場實施起來可能會齣現矛盾,此時首先需分析引起汽流激振的主要因素,然後採取能解決問題的關鍵措施,纔能取得滿意的效果.
모태300MW기륜궤적진동명현수도조문개계순서화개도대소적영향,통과대궤조적진동특정이급조문산생적기류력진행분석、연구발현:채용조정벌문적개계순서산생기류력래제고축승재하병불능감소혹소제해궤조적진동,반이증대료궤조적진동;원인시전자재기항중적경향위치발생료변화,개변료통류부분적간극;통과채취합리적조문개계순서화개도감소전자재기항중적편이,수연축승편심솔감소、축승재하하강,단시진동수평명현강저료.유차가지,억제기류격진적방법유약간충,유사방법재현장실시기래가능회출현모순,차시수선수분석인기기류격진적주요인소,연후채취능해결문제적관건조시,재능취득만의적효과.