石化技术与应用
石化技術與應用
석화기술여응용
PETROCHEMICAL TECHNOLOGY & APPLICATION
2011年
4期
320-323
,共4页
张永生%闫德兴%张凤华%娄世松%李飞%陈要君
張永生%閆德興%張鳳華%婁世鬆%李飛%陳要君
장영생%염덕흥%장봉화%루세송%리비%진요군
高酸原油%电脱盐%破乳剂%工艺条件
高痠原油%電脫鹽%破乳劑%工藝條件
고산원유%전탈염%파유제%공예조건
为解决某炼油厂加工高酸原油时出现的原油乳化严重、脱水脱盐不合格问题,通过模拟实验评选出了最佳破乳剂,并研究了工艺条件对电脱盐脱水效果的影响.结果表明,SH-2型破乳剂具有高效广谱性;在电场强度为600~800 V/cm,脱盐温度为125~130℃,破乳剂用量为25~30μg/g,注水量[m(水)/m(原油)]为6%的最佳工艺条件下,可将多-阿混合原油[m(多巴原油)/m(阿尔巴克拉原油)为1:2]和荣-马混合原油[m(荣卡多原油)/m(马希拉原油)为3:2]的含盐量由52.7,12.7 mg/L均降低至小于0.3 mg/L,脱盐脱水原油的含水质量分数均小于0.2%.
為解決某煉油廠加工高痠原油時齣現的原油乳化嚴重、脫水脫鹽不閤格問題,通過模擬實驗評選齣瞭最佳破乳劑,併研究瞭工藝條件對電脫鹽脫水效果的影響.結果錶明,SH-2型破乳劑具有高效廣譜性;在電場彊度為600~800 V/cm,脫鹽溫度為125~130℃,破乳劑用量為25~30μg/g,註水量[m(水)/m(原油)]為6%的最佳工藝條件下,可將多-阿混閤原油[m(多巴原油)/m(阿爾巴剋拉原油)為1:2]和榮-馬混閤原油[m(榮卡多原油)/m(馬希拉原油)為3:2]的含鹽量由52.7,12.7 mg/L均降低至小于0.3 mg/L,脫鹽脫水原油的含水質量分數均小于0.2%.
위해결모련유엄가공고산원유시출현적원유유화엄중、탈수탈염불합격문제,통과모의실험평선출료최가파유제,병연구료공예조건대전탈염탈수효과적영향.결과표명,SH-2형파유제구유고효엄보성;재전장강도위600~800 V/cm,탈염온도위125~130℃,파유제용량위25~30μg/g,주수량[m(수)/m(원유)]위6%적최가공예조건하,가장다-아혼합원유[m(다파원유)/m(아이파극랍원유)위1:2]화영-마혼합원유[m(영잡다원유)/m(마희랍원유)위3:2]적함염량유52.7,12.7 mg/L균강저지소우0.3 mg/L,탈염탈수원유적함수질량분수균소우0.2%.