实用口腔医学杂志
實用口腔醫學雜誌
실용구강의학잡지
JOURNAL OF PRACTICAL STOMATOLOGY
2009年
6期
824-827
,共4页
吴舜%何惠明%黄芳%高利欣%李锋%赵薇
吳舜%何惠明%黃芳%高利訢%李鋒%趙薇
오순%하혜명%황방%고리흔%리봉%조미
氟云母玻璃陶瓷%熔融铸造法%烧结法
氟雲母玻璃陶瓷%鎔融鑄造法%燒結法
불운모파리도자%용융주조법%소결법
Fluoro- mica glass ceramic%Melt- casting%Sintering
目的:研究不同制备工艺对齿科可切削氟云母玻璃陶瓷性能的影响.方法:采用熔融铸造工艺和烧结工艺制备K2O-MgO-MgF2-SiO2系统可切削氟云母玻璃陶瓷,采用XRD、SEM确定其晶相组成和微观结构,测试透射率、弯曲强度和脆性指数.结果: 2 种制备工艺制备的玻璃陶瓷主晶相均为四硅氟云母,晶相大小均为2~5 μm,径厚比6~7.烧结制备玻璃陶瓷晶相体积分数较高,透射率、脆性指数较低,弯曲强度较高.结论:针对氟云母玻璃陶瓷而言,烧结法制备工艺优于熔融铸造工艺.
目的:研究不同製備工藝對齒科可切削氟雲母玻璃陶瓷性能的影響.方法:採用鎔融鑄造工藝和燒結工藝製備K2O-MgO-MgF2-SiO2繫統可切削氟雲母玻璃陶瓷,採用XRD、SEM確定其晶相組成和微觀結構,測試透射率、彎麯彊度和脆性指數.結果: 2 種製備工藝製備的玻璃陶瓷主晶相均為四硅氟雲母,晶相大小均為2~5 μm,徑厚比6~7.燒結製備玻璃陶瓷晶相體積分數較高,透射率、脆性指數較低,彎麯彊度較高.結論:針對氟雲母玻璃陶瓷而言,燒結法製備工藝優于鎔融鑄造工藝.
목적:연구불동제비공예대치과가절삭불운모파리도자성능적영향.방법:채용용융주조공예화소결공예제비K2O-MgO-MgF2-SiO2계통가절삭불운모파리도자,채용XRD、SEM학정기정상조성화미관결구,측시투사솔、만곡강도화취성지수.결과: 2 충제비공예제비적파리도자주정상균위사규불운모,정상대소균위2~5 μm,경후비6~7.소결제비파리도자정상체적분수교고,투사솔、취성지수교저,만곡강도교고.결론:침대불운모파리도자이언,소결법제비공예우우용융주조공예.
Objective: To study the effects of the melt casting and the sintering methods on the machinability and other characteristics of K_2O-MgO-MgF_2-SiO_2 glass-ceramics. Methods: X-ray diffraction(XRD) and scanning electron microscopy (SEM)were used to examine the main crystal and the microstructure of the glass ceramics of the same composition which were made by melt casting and sintering methods, respectively. The transmissivity, flexural strength and brittleness index were observed respectively. Results: The glass ceramics made by two different methods have the same crystal, KMg_(2.5)Si_4O_(10)F_2, while the specimen prepared by the sintering method had lower transmissivity,better machinability and mechanical properties due to the higher mica volume percent. Conclusion; For production of fluoro-mica glass ceramics, sintering method has superiority compared to melt-casting method.