有机硅材料
有機硅材料
유궤규재료
SILICONE MATERIAL
2013年
4期
266-268
,共3页
胡新嵩%陈精华%黄德裕%余杰明%罗伟
鬍新嵩%陳精華%黃德裕%餘傑明%囉偉
호신숭%진정화%황덕유%여걸명%라위
有机硅%密封胶%防霉剂%防霉
有機硅%密封膠%防黴劑%防黴
유궤규%밀봉효%방매제%방매
silicone%sealant%anti-mildew agent%mildewproof
通过添加防霉剂,制备了防霉有机硅密封胶。比较了3种防霉剂对有机硅密封胶防霉性能的影响。结果表明,添加防霉剂后,有机硅密封胶的防霉性能明显提高,液体防霉剂的效果好于固体防霉剂;在防霉剂质量分数小于1.0%时,随着防霉剂用量的提高,其防霉等级逐渐提高;当防霉剂质量分数为1.0%时,有机硅密封胶的防霉等级达到0级。防霉有机硅密封胶的较佳配方为:80份107硅橡胶,20份201甲基硅油,8份气相法白炭黑,5份甲基三丁酮肟基硅烷,1份偶联剂,0.07份二月桂酸二丁基锡,1.14份防霉剂1。采用该配方制得的防霉有机硅密封胶工艺简单,综合性能稳定,符合GB/T 14683-2003理化性能和GB/T 1741-2007防霉性能0级的要求。
通過添加防黴劑,製備瞭防黴有機硅密封膠。比較瞭3種防黴劑對有機硅密封膠防黴性能的影響。結果錶明,添加防黴劑後,有機硅密封膠的防黴性能明顯提高,液體防黴劑的效果好于固體防黴劑;在防黴劑質量分數小于1.0%時,隨著防黴劑用量的提高,其防黴等級逐漸提高;噹防黴劑質量分數為1.0%時,有機硅密封膠的防黴等級達到0級。防黴有機硅密封膠的較佳配方為:80份107硅橡膠,20份201甲基硅油,8份氣相法白炭黑,5份甲基三丁酮肟基硅烷,1份偶聯劑,0.07份二月桂痠二丁基錫,1.14份防黴劑1。採用該配方製得的防黴有機硅密封膠工藝簡單,綜閤性能穩定,符閤GB/T 14683-2003理化性能和GB/T 1741-2007防黴性能0級的要求。
통과첨가방매제,제비료방매유궤규밀봉효。비교료3충방매제대유궤규밀봉효방매성능적영향。결과표명,첨가방매제후,유궤규밀봉효적방매성능명현제고,액체방매제적효과호우고체방매제;재방매제질량분수소우1.0%시,수착방매제용량적제고,기방매등급축점제고;당방매제질량분수위1.0%시,유궤규밀봉효적방매등급체도0급。방매유궤규밀봉효적교가배방위:80빈107규상효,20빈201갑기규유,8빈기상법백탄흑,5빈갑기삼정동우기규완,1빈우련제,0.07빈이월계산이정기석,1.14빈방매제1。채용해배방제득적방매유궤규밀봉효공예간단,종합성능은정,부합GB/T 14683-2003이화성능화GB/T 1741-2007방매성능0급적요구。
The mildew resistant silicone sealant was prepared by adding an anti-mildew agent .The influ-ence of 3 different anti-mildew agents on the mildew resistance of silicone sealant was investigated .Results show that silicone sealant with anti-mildew agent had good mildew resistance with the liquid anti-mildew agent being better than the solid one .The mildewproof grade of silicone sealant gradually improves with the content of anti-mildew agent the content of anti-mildew agent was less than 1.0 wt%.Furthermore, when the content of anti-mildew agent was 1.0 wt%, the mildewproof grade of silicone sealant was 0.Finally, the formula for mildew resistant silicone sealant is as follows:107 silicone rubber 80 phr, 201 methyl silicone oil 20 phr, fumed silica 8 phr, methyl tributyl ketone oxime silane 5 phr, coupling agent 1 phr, dibutyltin dilaurate 0.07 phr, and anti-mildew agent I 1.14 phr.The develped process is simple and stable , in line with the GB/T 14683-2003 and GB/T 2003-1741 of the requirements .