航天制造技术
航天製造技術
항천제조기술
HANGTIAN ZHIXAO JI SHU
2013年
4期
22-24
,共3页
王金雪%袁鸿%张国栋%余槐%肖志翔%江飞龙%刘忠
王金雪%袁鴻%張國棟%餘槐%肖誌翔%江飛龍%劉忠
왕금설%원홍%장국동%여괴%초지상%강비룡%류충
TC4钛合金%闪光对焊%组织%性能
TC4鈦閤金%閃光對銲%組織%性能
TC4태합금%섬광대한%조직%성능
TC4 titanium alloy%flash butt welding%microstructure%mechanical properties
针对TC4钛合金开展了闪光对焊试验,分析研究了接头在不同焊后热处理工艺下的组织和力学性能。结果表明:采用闪光对焊方法焊接TC4钛合金,能够获得优质的焊接接头。焊后固溶+时效状态下,接头的强度达到1104MPa,与同状态下母材等强;焊后普通退火状态下,接头强度低于固溶时效状态,但塑性和韧性高于固溶时效状态,且随着焊后退火温度的升高,接头的强度降低,塑性和韧性升高。
針對TC4鈦閤金開展瞭閃光對銲試驗,分析研究瞭接頭在不同銲後熱處理工藝下的組織和力學性能。結果錶明:採用閃光對銲方法銲接TC4鈦閤金,能夠穫得優質的銲接接頭。銲後固溶+時效狀態下,接頭的彊度達到1104MPa,與同狀態下母材等彊;銲後普通退火狀態下,接頭彊度低于固溶時效狀態,但塑性和韌性高于固溶時效狀態,且隨著銲後退火溫度的升高,接頭的彊度降低,塑性和韌性升高。
침대TC4태합금개전료섬광대한시험,분석연구료접두재불동한후열처리공예하적조직화역학성능。결과표명:채용섬광대한방법한접TC4태합금,능구획득우질적한접접두。한후고용+시효상태하,접두적강도체도1104MPa,여동상태하모재등강;한후보통퇴화상태하,접두강도저우고용시효상태,단소성화인성고우고용시효상태,차수착한후퇴화온도적승고,접두적강도강저,소성화인성승고。
Flash butt welding experiments of TC4 Titanium Alloy were carried out, then the microstructure and properties of the joints under the different post weld heat treatment procedures were studied. Results indicate that flash butt welding is suitable to weld the TC4 titanium alloy, and can gain the high quality joint. Under solution and aging condition, the tensile strength of the welded joints achieve 1104MPa, which is equal to the basic metal at the same condition. While ordinary annealing after welding,the tensile strength of the welded joints is lower than that under the condition of solution and aging, and the elongation and impact toughness are higher than that under the condition of solution and aging. Along with the increased annealing temperature,the tensile strength of the welded joints is reduced and the elongation and impact toughness is increased.