润滑与密封
潤滑與密封
윤활여밀봉
LUBRICATION ENGINEERING
2013年
9期
46-49,53
,共5页
粗糙度%黏度%综合速度%接触应力
粗糙度%黏度%綜閤速度%接觸應力
조조도%점도%종합속도%접촉응력
surface roughness%viscosity%entrainment velocity%contact stress
基于真实测量的齿面粗糙度数值,利用傅里叶非线性回归原理,生成近似真实齿面粗糙度曲线方程。在固定单位齿宽载荷的情况下,采用多重网格法分析润滑油黏度和齿面综合速度之乘积固定不变而同时改变其中任一量时,对油膜厚度以及轮齿接触应力的影响,得出油膜平均厚度以及齿轮次表面剪应力的相应数值解。计算结果表明:在全膜润滑中,在上述条件下同时改变黏度和齿面综合速度其中任一量对油膜厚度以及轮齿接触应力影响不大;而在混合润滑中,随着黏度的增大,平均油膜厚度增加,齿面接触应力减小。
基于真實測量的齒麵粗糙度數值,利用傅裏葉非線性迴歸原理,生成近似真實齒麵粗糙度麯線方程。在固定單位齒寬載荷的情況下,採用多重網格法分析潤滑油黏度和齒麵綜閤速度之乘積固定不變而同時改變其中任一量時,對油膜厚度以及輪齒接觸應力的影響,得齣油膜平均厚度以及齒輪次錶麵剪應力的相應數值解。計算結果錶明:在全膜潤滑中,在上述條件下同時改變黏度和齒麵綜閤速度其中任一量對油膜厚度以及輪齒接觸應力影響不大;而在混閤潤滑中,隨著黏度的增大,平均油膜厚度增加,齒麵接觸應力減小。
기우진실측량적치면조조도수치,이용부리협비선성회귀원리,생성근사진실치면조조도곡선방정。재고정단위치관재하적정황하,채용다중망격법분석윤활유점도화치면종합속도지승적고정불변이동시개변기중임일량시,대유막후도이급륜치접촉응력적영향,득출유막평균후도이급치륜차표면전응력적상응수치해。계산결과표명:재전막윤활중,재상술조건하동시개변점도화치면종합속도기중임일량대유막후도이급륜치접촉응력영향불대;이재혼합윤활중,수착점도적증대,평균유막후도증가,치면접촉응력감소。
The approximate tooth surface roughness equation was set up by using Fourier nonlinear approximation meth-od based on the actually measured roughness.Under the constant unit tooth width load,the influences on oil film thickness and gearing contact stress were analyzed by Multigrid method,when changing any one value of the lubricant viscosity and the teeth surface entrainment velocity simultaneously and fixing their product.The results show that,under full film lubri-cation,it has no influence on oil film thickness and gearing contact stress to change any one value of the lubricant viscosity and the teeth surface entrainment velocity simultaneously in the above conditions.However under mixed lubrication,the average film thickness is increased and gearing contact stress is decreased along with the increasing of the lubricant viscosi-ty.