实用口腔医学杂志
實用口腔醫學雜誌
실용구강의학잡지
JOURNAL OF PRACTICAL STOMATOLOGY
2014年
4期
535-537
,共3页
张兴%陈松龄%张云%黄代营
張興%陳鬆齡%張雲%黃代營
장흥%진송령%장운%황대영
眶部种植体%应力分布%三维有限元%过盈量
眶部種植體%應力分佈%三維有限元%過盈量
광부충식체%응력분포%삼유유한원%과영량
Orbital implant%Stress distribution%Three-dimensional finite element%Shrink range
目的:探讨不同过盈量的眶部种植体对骨界面应力分布的影响。方法:建立4种规格种植体过盈量分别为0.05、0.1、0.15 mm的眶部种植体-颅颌面骨三维有限元模型,计算并分析不同情况下的应力分布。结果:骨界面应力随着过盈量增大而增大,但在0.15 mm过盈量时,骨界面应力降低。10 mm种植体在0.1 mm及0.15 mm过盈量条件下界面应力值明显低于其他规格种植体。结论:0.1 mm过盈量符合临床要求,在眶部种植手术设计时因考虑长度和过盈量的影响。
目的:探討不同過盈量的眶部種植體對骨界麵應力分佈的影響。方法:建立4種規格種植體過盈量分彆為0.05、0.1、0.15 mm的眶部種植體-顱頜麵骨三維有限元模型,計算併分析不同情況下的應力分佈。結果:骨界麵應力隨著過盈量增大而增大,但在0.15 mm過盈量時,骨界麵應力降低。10 mm種植體在0.1 mm及0.15 mm過盈量條件下界麵應力值明顯低于其他規格種植體。結論:0.1 mm過盈量符閤臨床要求,在眶部種植手術設計時因攷慮長度和過盈量的影響。
목적:탐토불동과영량적광부충식체대골계면응력분포적영향。방법:건립4충규격충식체과영량분별위0.05、0.1、0.15 mm적광부충식체-로합면골삼유유한원모형,계산병분석불동정황하적응력분포。결과:골계면응력수착과영량증대이증대,단재0.15 mm과영량시,골계면응력강저。10 mm충식체재0.1 mm급0.15 mm과영량조건하계면응력치명현저우기타규격충식체。결론:0.1 mm과영량부합림상요구,재광부충식수술설계시인고필장도화과영량적영향。
Objective:To observe the effect of orbital implant shrink range on the stress distribution in bone-implant interface. Methods:The 3D finite element analysis of craniofacial and orbital implant models with the implant length of 3,4,6 and 10 mm,and with the shrink range of0.05,0.1 and 0.15 mm were established respectively.The stress in the bone-implant interface were calculat-ed and analyzed.Results:The stress increased with the increase of implant shrink range.The stress produced by the implant with 0.15 mm shrink range decreased.The stress of the implant of 10 mm was lower than that of other implants with the shrink range of 0.1 and 0.15 mm.Conclusion:The maximal implant shrink range of 0.1 mm in the model can meet the clinical requirements in orbital implant planning.