工程塑料应用
工程塑料應用
공정소료응용
ENGINEERING PLASTICS APPLICATION
2014年
4期
19-22
,共4页
聚乳酸%聚乙烯%共混物%力学性能%亲水性
聚乳痠%聚乙烯%共混物%力學性能%親水性
취유산%취을희%공혼물%역학성능%친수성
polylactic acid%polyethylene%blend%mechanical property%hydrophilicity
利用熔融成型法制得不同聚乳酸(PLA)质量分数的低密度聚乙烯/聚乳酸(PE-LD/PLA)共混物,并对PE-LD/PLA共混物的结构和性能进行研究。结果表明,共混物中PLA相与PE-LD相之间没有发生化学反应,它是PLA与PE-LD的一种简单混合物。共混物中的PLA含量对其力学性能和亲水性均有很大影响。随着PLA含量的增加,共混物的断裂伸长率逐渐降低而拉伸强度和拉伸弹性模量逐渐增大,共混物的亲水性增加,且随着降解时间的增加,共混物的断裂伸长率轻微增加而拉伸强度和拉伸弹性模量小幅度降低,这些现象均与PLA是一种强度高但柔韧性较差的亲水性高分子材料有关。
利用鎔融成型法製得不同聚乳痠(PLA)質量分數的低密度聚乙烯/聚乳痠(PE-LD/PLA)共混物,併對PE-LD/PLA共混物的結構和性能進行研究。結果錶明,共混物中PLA相與PE-LD相之間沒有髮生化學反應,它是PLA與PE-LD的一種簡單混閤物。共混物中的PLA含量對其力學性能和親水性均有很大影響。隨著PLA含量的增加,共混物的斷裂伸長率逐漸降低而拉伸彊度和拉伸彈性模量逐漸增大,共混物的親水性增加,且隨著降解時間的增加,共混物的斷裂伸長率輕微增加而拉伸彊度和拉伸彈性模量小幅度降低,這些現象均與PLA是一種彊度高但柔韌性較差的親水性高分子材料有關。
이용용융성형법제득불동취유산(PLA)질량분수적저밀도취을희/취유산(PE-LD/PLA)공혼물,병대PE-LD/PLA공혼물적결구화성능진행연구。결과표명,공혼물중PLA상여PE-LD상지간몰유발생화학반응,타시PLA여PE-LD적일충간단혼합물。공혼물중적PLA함량대기역학성능화친수성균유흔대영향。수착PLA함량적증가,공혼물적단렬신장솔축점강저이랍신강도화랍신탄성모량축점증대,공혼물적친수성증가,차수착강해시간적증가,공혼물적단렬신장솔경미증가이랍신강도화랍신탄성모량소폭도강저,저사현상균여PLA시일충강도고단유인성교차적친수성고분자재료유관。
The low-density polyethylene/polylactic acid(PE-LD/PLA) blends with various contents of PLA were prepared by using melt-blending method firstly,then the structure of the blends and the influences of PLA content on the mechanical properties and hydrophilicity of these prepared samples were investigated. The results show that the blends is a simple hybrid of pure PE-LD and PLA. The PLA content influences on the mechanical properties and hydrophilicity of the blends,with the increasing of PLA content,the elongation at break decreases gradually,the tensile strength and the tensile modulus of elasticity increase,and the hydrophilicity increases. With the increasing of degradation time,the elongation at break increases slightly,but the tensile strength and the tensile modulus of elasticity decrease slightly. All these changes are attributed to the high strength,low ductibility and well hydrophilicity of the PLA.