材料工程
材料工程
재료공정
JOURNAL OF MATERIALS ENGINEERING
2013年
9期
38-43
,共6页
庄栋栋%王作成%张建强%陈陪敦%陈坤%马正伟%谷国华
莊棟棟%王作成%張建彊%陳陪敦%陳坤%馬正偉%穀國華
장동동%왕작성%장건강%진배돈%진곤%마정위%곡국화
低碳铝镇静钢板%再结晶%硬度%织构
低碳鋁鎮靜鋼闆%再結晶%硬度%織構
저탄려진정강판%재결정%경도%직구
low carbon Al-killed steel sheet%recrystallization%hardness%texture
将不同冷轧压下率的低碳铝镇静钢进行不同保温温度和时间的退火再结晶实验研究,利用维氏硬度计、金相显微镜和X射线衍射仪研究了退火后试样的硬度、金相显微组织及织构的变化情况.结果表明:在相同的退火工艺制度条件下,随着冷轧压下率的增加,再结晶开始和结束温度降低,晶粒尺寸减小.当冷轧压下率升高到68%后,冷轧压下率的增加对再结晶晶粒细化的作用减弱,甚至没有细化作用;680℃保温退火时,一开始就发生了再结晶,基本不需要孕育期.随着保温时间的延长,晶粒均匀长大,晶粒饼形程度增加;退火温度由660℃升高到720℃时,{111}面有利织构增加,{100}面不利织构减少,720℃退火温度较为适宜.冷轧压下率为58%的试样在760℃退火时发生了二次再结晶对实验钢板的力学性能产生不利影响.
將不同冷軋壓下率的低碳鋁鎮靜鋼進行不同保溫溫度和時間的退火再結晶實驗研究,利用維氏硬度計、金相顯微鏡和X射線衍射儀研究瞭退火後試樣的硬度、金相顯微組織及織構的變化情況.結果錶明:在相同的退火工藝製度條件下,隨著冷軋壓下率的增加,再結晶開始和結束溫度降低,晶粒呎吋減小.噹冷軋壓下率升高到68%後,冷軋壓下率的增加對再結晶晶粒細化的作用減弱,甚至沒有細化作用;680℃保溫退火時,一開始就髮生瞭再結晶,基本不需要孕育期.隨著保溫時間的延長,晶粒均勻長大,晶粒餅形程度增加;退火溫度由660℃升高到720℃時,{111}麵有利織構增加,{100}麵不利織構減少,720℃退火溫度較為適宜.冷軋壓下率為58%的試樣在760℃退火時髮生瞭二次再結晶對實驗鋼闆的力學性能產生不利影響.
장불동랭알압하솔적저탄려진정강진행불동보온온도화시간적퇴화재결정실험연구,이용유씨경도계、금상현미경화X사선연사의연구료퇴화후시양적경도、금상현미조직급직구적변화정황.결과표명:재상동적퇴화공예제도조건하,수착랭알압하솔적증가,재결정개시화결속온도강저,정립척촌감소.당랭알압하솔승고도68%후,랭알압하솔적증가대재결정정립세화적작용감약,심지몰유세화작용;680℃보온퇴화시,일개시취발생료재결정,기본불수요잉육기.수착보온시간적연장,정립균균장대,정립병형정도증가;퇴화온도유660℃승고도720℃시,{111}면유리직구증가,{100}면불리직구감소,720℃퇴화온도교위괄의.랭알압하솔위58%적시양재760℃퇴화시발생료이차재결정대실험강판적역학성능산생불리영향.