长春工业大学学报(自然科学版)
長春工業大學學報(自然科學版)
장춘공업대학학보(자연과학판)
JOURNAL OF CHANGCHUN UNIVERSITY OF TECHNOLOGY(NATURAL SCIENCE EDITION)
2013年
3期
247-252
,共6页
杨得超%王淮%刘威%谢争先
楊得超%王淮%劉威%謝爭先
양득초%왕회%류위%사쟁선
铁素体不锈钢%无填丝TIG焊%组织形貌%抗拉强度
鐵素體不鏽鋼%無填絲TIG銲%組織形貌%抗拉彊度
철소체불수강%무전사TIG한%조직형모%항랍강도
对022Cr11Ti钢汽车排气管管缝进行无填丝双TIG焊枪自动焊接试验结果表明,焊接工艺参数对接头的组织形貌及抗拉强度影响较大,双焊枪电流在90~130 A范围内焊缝表面质量较好,但都会使接头晶粒不同程度长大,随着焊接电流增大,焊缝组织形貌由粗大柱状晶形貌改变为心部等轴晶+两侧粗大柱状晶形貌,同时,Rm逐步降低,拉伸断裂位置也按HTHAZ→焊缝→HTHAZ改变,试验得出采用双枪电流分别为I1=120 A,I2=90 A时的管缝接头具有较好的强度,Rm可达到376.81MPa,使焊管冷弯时发生接头开裂现象得到明显改善.
對022Cr11Ti鋼汽車排氣管管縫進行無填絲雙TIG銲鎗自動銲接試驗結果錶明,銲接工藝參數對接頭的組織形貌及抗拉彊度影響較大,雙銲鎗電流在90~130 A範圍內銲縫錶麵質量較好,但都會使接頭晶粒不同程度長大,隨著銲接電流增大,銲縫組織形貌由粗大柱狀晶形貌改變為心部等軸晶+兩側粗大柱狀晶形貌,同時,Rm逐步降低,拉伸斷裂位置也按HTHAZ→銲縫→HTHAZ改變,試驗得齣採用雙鎗電流分彆為I1=120 A,I2=90 A時的管縫接頭具有較好的彊度,Rm可達到376.81MPa,使銲管冷彎時髮生接頭開裂現象得到明顯改善.
대022Cr11Ti강기차배기관관봉진행무전사쌍TIG한창자동한접시험결과표명,한접공예삼수대접두적조직형모급항랍강도영향교대,쌍한창전류재90~130 A범위내한봉표면질량교호,단도회사접두정립불동정도장대,수착한접전류증대,한봉조직형모유조대주상정형모개변위심부등축정+량측조대주상정형모,동시,Rm축보강저,랍신단렬위치야안HTHAZ→한봉→HTHAZ개변,시험득출채용쌍창전류분별위I1=120 A,I2=90 A시적관봉접두구유교호적강도,Rm가체도376.81MPa,사한관랭만시발생접두개렬현상득도명현개선.