材料导报
材料導報
재료도보
MATERIALS REVIEW
2014年
10期
113-115,131
,共4页
朱登玲%彭家惠%赵敏%李志新%王彩霞
硃登玲%彭傢惠%趙敏%李誌新%王綵霞
주등령%팽가혜%조민%리지신%왕채하
石英砂%陶瓷模具石膏%抗折强度%吸水率%磨损率
石英砂%陶瓷模具石膏%抗摺彊度%吸水率%磨損率
석영사%도자모구석고%항절강도%흡수솔%마손솔
silicate sand%ceramic model-gypsum%flexural strength%water absorption%abrasion rate
研究了0~0.4 mm石英砂对模具石膏凝结时间、抗折强度、吸水率及磨损率的影响,并采用MIP测试技术分析石膏-石英砂增强机理.结果表明:当石英砂掺量为10%时,模具石膏2h及干态抗折强度增加显著且均达到峰值,分别为3.29 MPa、6.36 MPa,较空白样增幅高达20.73%、24.95%.随着石英砂掺量的增加,模具石膏的磨损率逐渐降低,耐磨性逐渐增强,当掺量为20%时,其磨损率为0.96%,较空白样降幅高达72%.吸水率则随着石英砂掺量的增加有小幅度降低.因此,为满足模具石膏的综合性能,石英砂的最佳掺量为10%.
研究瞭0~0.4 mm石英砂對模具石膏凝結時間、抗摺彊度、吸水率及磨損率的影響,併採用MIP測試技術分析石膏-石英砂增彊機理.結果錶明:噹石英砂摻量為10%時,模具石膏2h及榦態抗摺彊度增加顯著且均達到峰值,分彆為3.29 MPa、6.36 MPa,較空白樣增幅高達20.73%、24.95%.隨著石英砂摻量的增加,模具石膏的磨損率逐漸降低,耐磨性逐漸增彊,噹摻量為20%時,其磨損率為0.96%,較空白樣降幅高達72%.吸水率則隨著石英砂摻量的增加有小幅度降低.因此,為滿足模具石膏的綜閤性能,石英砂的最佳摻量為10%.
연구료0~0.4 mm석영사대모구석고응결시간、항절강도、흡수솔급마손솔적영향,병채용MIP측시기술분석석고-석영사증강궤리.결과표명:당석영사참량위10%시,모구석고2h급간태항절강도증가현저차균체도봉치,분별위3.29 MPa、6.36 MPa,교공백양증폭고체20.73%、24.95%.수착석영사참량적증가,모구석고적마손솔축점강저,내마성축점증강,당참량위20%시,기마손솔위0.96%,교공백양강폭고체72%.흡수솔칙수착석영사참량적증가유소폭도강저.인차,위만족모구석고적종합성능,석영사적최가참량위10%.