兵工自动化
兵工自動化
병공자동화
ORDNANCE INDUSTRY AUTOMATION
2013年
11期
52-56
,共5页
刁小强%王彩玲%赵省向%封雪松%李文祥
刁小彊%王綵玲%趙省嚮%封雪鬆%李文祥
조소강%왕채령%조성향%봉설송%리문상
分步压装%工艺参数%压力%螺杆%密度分布
分步壓裝%工藝參數%壓力%螺桿%密度分佈
분보압장%공예삼수%압력%라간%밀도분포
step-press-loading charges%technological parameter%pressure%screw%density distribution
用模拟药和可退模开合弹对不同分步压装装药工艺参数进行实验,并对装药密度和轴径向密度分布进行检测,分析分步压装工艺参数变化对最终装药密度和密度分布的影响。试验结果表明:随着螺杆直径的增大,周边和平均装药密度均呈上升的趋势;装药过程中初始压力越高,越有利于提高装药密度和密度分布,当压力达到一定值后,装药密度趋于一致;螺杆距弹体底部间距越小,底部越容易压实,密度越高;螺杆每次带入的进料量越少,压制次数越多,密度均匀性越高。该研究为加快分步压装装药工艺的推广应用打下了基础。
用模擬藥和可退模開閤彈對不同分步壓裝裝藥工藝參數進行實驗,併對裝藥密度和軸徑嚮密度分佈進行檢測,分析分步壓裝工藝參數變化對最終裝藥密度和密度分佈的影響。試驗結果錶明:隨著螺桿直徑的增大,週邊和平均裝藥密度均呈上升的趨勢;裝藥過程中初始壓力越高,越有利于提高裝藥密度和密度分佈,噹壓力達到一定值後,裝藥密度趨于一緻;螺桿距彈體底部間距越小,底部越容易壓實,密度越高;螺桿每次帶入的進料量越少,壓製次數越多,密度均勻性越高。該研究為加快分步壓裝裝藥工藝的推廣應用打下瞭基礎。
용모의약화가퇴모개합탄대불동분보압장장약공예삼수진행실험,병대장약밀도화축경향밀도분포진행검측,분석분보압장공예삼수변화대최종장약밀도화밀도분포적영향。시험결과표명:수착라간직경적증대,주변화평균장약밀도균정상승적추세;장약과정중초시압력월고,월유리우제고장약밀도화밀도분포,당압력체도일정치후,장약밀도추우일치;라간거탄체저부간거월소,저부월용역압실,밀도월고;라간매차대입적진료량월소,압제차수월다,밀도균균성월고。해연구위가쾌분보압장장약공예적추엄응용타하료기출。
Analog explosive and unmoulded shot were employed to experiment the different parameters, and detection density distribution of charges and axes radial, analyzed the effect of step-press-loading technological parameter for finally charge density and density distribution. The results show that, the effects on charge density and density distribution of step-press-loading charge technology are observed obviously. The average charge densities are enhanced with the increasing screw diameters, charge quality and density distributions are also improved with the increasing pressures. When the bottom gap of shot decreases, shot bottom can be pressed more easily, and the charge density can be improved at the same time. The press frequency and density uniformity can be promoted with the decreasing charge quantity. This research will promote the use of the step-press-loading charges technological.