湖北工业大学学报
湖北工業大學學報
호북공업대학학보
JOURNAL OF HUBEI UNIVERSITY OF TECHNOLOGY
2014年
1期
84-86
,共3页
钳制器%螺栓%力学分析%螺纹强度%螺距
鉗製器%螺栓%力學分析%螺紋彊度%螺距
겸제기%라전%역학분석%라문강도%라거
clamping-device%bolt%stress analysis%strength of thread%pitch
针对某款液压常闭型钳制器提供钳制力的螺栓,分析其受力情况与安全系数,验证了车去中段螺纹的螺栓直径为9 mm的光杆部分能够承受钳制器所需要的巨大的钳制力,但是在重新设计时,应当将光杆部分的直径尽量取得大一些,保证螺杆不会被拉坏。同时验证了大径为12 mm 的螺栓,各螺距对螺纹强度影响不大,并给出了不同大径不同螺距的普通螺纹危险截面的切应力与弯曲应力的计算公式,为替换其他标准和选用合适的国标普通螺纹提供了理论依据。
針對某款液壓常閉型鉗製器提供鉗製力的螺栓,分析其受力情況與安全繫數,驗證瞭車去中段螺紋的螺栓直徑為9 mm的光桿部分能夠承受鉗製器所需要的巨大的鉗製力,但是在重新設計時,應噹將光桿部分的直徑儘量取得大一些,保證螺桿不會被拉壞。同時驗證瞭大徑為12 mm 的螺栓,各螺距對螺紋彊度影響不大,併給齣瞭不同大徑不同螺距的普通螺紋危險截麵的切應力與彎麯應力的計算公式,為替換其他標準和選用閤適的國標普通螺紋提供瞭理論依據。
침대모관액압상폐형겸제기제공겸제력적라전,분석기수력정황여안전계수,험증료차거중단라문적라전직경위9 mm적광간부분능구승수겸제기소수요적거대적겸제력,단시재중신설계시,응당장광간부분적직경진량취득대일사,보증라간불회피랍배。동시험증료대경위12 mm 적라전,각라거대라문강도영향불대,병급출료불동대경불동라거적보통라문위험절면적절응력여만곡응력적계산공식,위체환기타표준화선용합괄적국표보통라문제공료이론의거。
Focusing on some hydraulic normal closed clamping device′s bolts which are the source of clam-ping force,the paper analyzed its stress situation and safety factor.It then verified that the 9 mm diameter of rod section of the bolt which was turned off can bear the huge clamping force of the clamping device. When re-designed,the diameter of rod section should be as larger as possible,to ensure that the bolt wouldn′t produce plastic deformation.It also verified that the 12mm nominal diameter′bolt,different pit-ches make little difference in the bolt thread strength,and gave the strength formula of shear stress and bending stress on the dangerous section of various pitches of different nominal diameter,so as to provide the theoretical basis of replacing other standards and choosing the suitable GB common thread.