工业仪表与自动化装置
工業儀錶與自動化裝置
공업의표여자동화장치
INDUSTRIAL INSTRUMENTATION & AUTOMATION
2014年
1期
98-101
,共4页
数字存储示波器%Matlab%数字内插
數字存儲示波器%Matlab%數字內插
수자존저시파기%Matlab%수자내삽
digital storage oscilloscope%Matlab%digital interpolation
数字存储示波器在快时基档位工作时,由于实时采样率不够,仅能采集信号的少数样点,为了重构信号,必须进行插值。通过编程和仿真比较了三次样条插值、分段线性插值、三次插值、最邻近插值对几种不同波形的恢复结果,并计算和分析了相关的均方误差。考虑实际待测的信号的不可知性和复杂性,并权衡精度与速度,当待插信号的点数小于100点时,选用三次样条插值;当待插信号的点数不小于100点时,采用三次插值法。 Matlab仿真表明,设计结果的各项性能指标均达到指定要求,设计过程简便易行。
數字存儲示波器在快時基檔位工作時,由于實時採樣率不夠,僅能採集信號的少數樣點,為瞭重構信號,必鬚進行插值。通過編程和倣真比較瞭三次樣條插值、分段線性插值、三次插值、最鄰近插值對幾種不同波形的恢複結果,併計算和分析瞭相關的均方誤差。攷慮實際待測的信號的不可知性和複雜性,併權衡精度與速度,噹待插信號的點數小于100點時,選用三次樣條插值;噹待插信號的點數不小于100點時,採用三次插值法。 Matlab倣真錶明,設計結果的各項性能指標均達到指定要求,設計過程簡便易行。
수자존저시파기재쾌시기당위공작시,유우실시채양솔불구,부능채집신호적소수양점,위료중구신호,필수진행삽치。통과편정화방진비교료삼차양조삽치、분단선성삽치、삼차삽치、최린근삽치대궤충불동파형적회복결과,병계산화분석료상관적균방오차。고필실제대측적신호적불가지성화복잡성,병권형정도여속도,당대삽신호적점수소우100점시,선용삼차양조삽치;당대삽신호적점수불소우100점시,채용삼차삽치법。 Matlab방진표명,설계결과적각항성능지표균체도지정요구,설계과정간편역행。
At high sweep rates , only a few samples of the signals can be on digital storage oscillo-scope screen .To give the user a reasonable view of the signals and to measure their parameters accurate-ly, interpolation is necessary .The piecewise cubic interpolations , the piecewise linear interpolation , the piecewise nearest interpolation , the cubic spline interpolation of several different waveform of the resump-tion of results have been compared through programming and simulation and the relevant root mean squre error calculated and analyzed .To take into account the actual measured signal of the unpredictability and complexity , and weigh the accuracy and speed , the choice of the cubic spline interpolation is applied when the signal is less than 100 points , when the point of the signal into question is not less than 100 points, the piecewise cubic interpolation is applied .The design process based on Matlab is very simple and practical .