中国有色金属学报
中國有色金屬學報
중국유색금속학보
THE CHINESE JOURNAL OF NONFERROUS METALS
2014年
2期
310-316
,共7页
吴远志%严红革%朱素琴%陈吉华%刘先兰%刘安民
吳遠誌%嚴紅革%硃素琴%陳吉華%劉先蘭%劉安民
오원지%엄홍혁%주소금%진길화%류선란%류안민
ZK60镁合金%多向锻造%显微组织%力学性能
ZK60鎂閤金%多嚮鍛造%顯微組織%力學性能
ZK60미합금%다향단조%현미조직%역학성능
ZK60 magnesium alloy%triaxial-forging%microstructure%mechanical property
采用空气锤对ZK60镁合金进行多向锻造变形,研究锻坯的组织演变以及组织和性能均匀性。结果表明,锻锤与锻坯之间摩擦力的作用造成不均匀变形,使锻坯芯部的实际变形量大于边部的。累积应变∑Δε=3.3时,锻坯芯部组织为蜂窝状粗大再结晶组织和岛状细小再结晶组织,而边部组织则由蜂窝状粗大再结晶组织和呈岛状分布的孪晶组成;其抗拉强度从边部到芯部逐渐降低,而伸长率则由边部向芯部逐渐升高。锻坯力学性能存在一定的各向异性,但锻坯各方向抗拉强度在310.6~323.9 MPa之间,伸长率在21.9%~29.7%之间,表明该工艺可以有效地避免强烈的各向异性,是制备高性能变形镁合金的理想工艺。
採用空氣錘對ZK60鎂閤金進行多嚮鍛造變形,研究鍛坯的組織縯變以及組織和性能均勻性。結果錶明,鍛錘與鍛坯之間摩抆力的作用造成不均勻變形,使鍛坯芯部的實際變形量大于邊部的。纍積應變∑Δε=3.3時,鍛坯芯部組織為蜂窩狀粗大再結晶組織和島狀細小再結晶組織,而邊部組織則由蜂窩狀粗大再結晶組織和呈島狀分佈的孿晶組成;其抗拉彊度從邊部到芯部逐漸降低,而伸長率則由邊部嚮芯部逐漸升高。鍛坯力學性能存在一定的各嚮異性,但鍛坯各方嚮抗拉彊度在310.6~323.9 MPa之間,伸長率在21.9%~29.7%之間,錶明該工藝可以有效地避免彊烈的各嚮異性,是製備高性能變形鎂閤金的理想工藝。
채용공기추대ZK60미합금진행다향단조변형,연구단배적조직연변이급조직화성능균균성。결과표명,단추여단배지간마찰력적작용조성불균균변형,사단배심부적실제변형량대우변부적。루적응변∑Δε=3.3시,단배심부조직위봉와상조대재결정조직화도상세소재결정조직,이변부조직칙유봉와상조대재결정조직화정도상분포적련정조성;기항랍강도종변부도심부축점강저,이신장솔칙유변부향심부축점승고。단배역학성능존재일정적각향이성,단단배각방향항랍강도재310.6~323.9 MPa지간,신장솔재21.9%~29.7%지간,표명해공예가이유효지피면강렬적각향이성,시제비고성능변형미합금적이상공예。
Triaxial-forging of ZK60 magnesium alloy was conducted on air hammer, and the microstructure evolution and the homogeneity of microstructures and properties were investigated. The result show that inhomogeneous deformation is detected in the forged specimen due to the friction between the hammer and specimen, and the actual deformation at the central part of the specimen is extensively larger than that at other part. A mixed structure of honeycomb-like coarse dynamic recrystallization (DRX) grains and island-like ultrafine DRX grains are obtained at the central part of the specimen at accumulated strain∑Δεof 3.3, while the structure at the edge part of the specimen consists of honeycomb-like coarse DRX grains and island-like twins. The ultimate tensile strength (UTS) decreases while the ductility increases from the edge part to centre part of the specimen at∑Δεof 3.3. Mechanical anisotropy is also detected in the forged specimen at ∑Δε of 3.3. However, the UTS and elongations at different directions range in 310.6-323.9 MPa and 21.9%-29.7%, respectively, which indicates that extensive anisotropy can be avoided by high strain rate triaxial forging technique. High strain rate triaxial forging is therefore identified as a potential technique for producing wrought magnesium with excellent mechanical properties.