中国组织工程研究
中國組織工程研究
중국조직공정연구
Journal of Clinical Rehabilitative Tissue Engineering Research
2014年
13期
1969-1974
,共6页
许杰%马若凡%蔡志清%李登
許傑%馬若凡%蔡誌清%李登
허걸%마약범%채지청%리등
植入物%人工假体%发育不良%全髋关节置换%关节成形术%有限元分析%生物力学
植入物%人工假體%髮育不良%全髖關節置換%關節成形術%有限元分析%生物力學
식입물%인공가체%발육불량%전관관절치환%관절성형술%유한원분석%생물역학
arthroplasty,replacement,hip%hip joint%acetabulum%finite element analysis%biomechanics
背景:成人髋臼发育不良髋臼小而浅,臼内有大量骨痂和瘢痕组织等都为人工髋关节置换臼杯安装带来极大困难。臼杯安装后局部的力学变化关系到置换后假体松动的发生及使用寿命。<br> 目的:利用三维有限元力学分析方法,对髋关节发育不良患者采用不同直径臼杯置入,观察对髋臼假体-骨界面间应力分布情况的影响。<br> 方法:选取髋关节发育不良患者的骨盆为试验对象,用螺旋 CT 做全长连续扫描,然后利用计算机仿真技术对 CT 图像进行三维重建,建立髋关节发育不良骨盆模型。在计算机环境中对重建模型进行不同直径臼杯置入的模拟手术,利用有限元分析软件对重建模型进行有限元网格化及力学分析。<br> 结果与结论:对于髋臼发育不良的病例,选择小直径臼杯可应对髋臼浅平、骨床骨量不足的缺陷而达到较好的臼杯骨床包容,但臼杯直径小致接触面小使单位面积应力升高;另一方面,大直径臼杯置入扩大磨锉髋臼骨床可引起髋内壁破损突破,导致应力(包括压应力及剪切力)增大及集中。由此推断,髋臼发育不良全髋关节置换时应在保证骨床包容的前提下选择较大直径的臼杯,有利于应力的良好分布,但应尽量避免或减少扩大磨锉髋臼骨床所致髋臼内壁的穿破。
揹景:成人髖臼髮育不良髖臼小而淺,臼內有大量骨痂和瘢痕組織等都為人工髖關節置換臼杯安裝帶來極大睏難。臼杯安裝後跼部的力學變化關繫到置換後假體鬆動的髮生及使用壽命。<br> 目的:利用三維有限元力學分析方法,對髖關節髮育不良患者採用不同直徑臼杯置入,觀察對髖臼假體-骨界麵間應力分佈情況的影響。<br> 方法:選取髖關節髮育不良患者的骨盆為試驗對象,用螺鏇 CT 做全長連續掃描,然後利用計算機倣真技術對 CT 圖像進行三維重建,建立髖關節髮育不良骨盆模型。在計算機環境中對重建模型進行不同直徑臼杯置入的模擬手術,利用有限元分析軟件對重建模型進行有限元網格化及力學分析。<br> 結果與結論:對于髖臼髮育不良的病例,選擇小直徑臼杯可應對髖臼淺平、骨床骨量不足的缺陷而達到較好的臼杯骨床包容,但臼杯直徑小緻接觸麵小使單位麵積應力升高;另一方麵,大直徑臼杯置入擴大磨銼髖臼骨床可引起髖內壁破損突破,導緻應力(包括壓應力及剪切力)增大及集中。由此推斷,髖臼髮育不良全髖關節置換時應在保證骨床包容的前提下選擇較大直徑的臼杯,有利于應力的良好分佈,但應儘量避免或減少擴大磨銼髖臼骨床所緻髖臼內壁的穿破。
배경:성인관구발육불량관구소이천,구내유대량골가화반흔조직등도위인공관관절치환구배안장대래겁대곤난。구배안장후국부적역학변화관계도치환후가체송동적발생급사용수명。<br> 목적:이용삼유유한원역학분석방법,대관관절발육불량환자채용불동직경구배치입,관찰대관구가체-골계면간응력분포정황적영향。<br> 방법:선취관관절발육불량환자적골분위시험대상,용라선 CT 주전장련속소묘,연후이용계산궤방진기술대 CT 도상진행삼유중건,건립관관절발육불량골분모형。재계산궤배경중대중건모형진행불동직경구배치입적모의수술,이용유한원분석연건대중건모형진행유한원망격화급역학분석。<br> 결과여결론:대우관구발육불량적병례,선택소직경구배가응대관구천평、골상골량불족적결함이체도교호적구배골상포용,단구배직경소치접촉면소사단위면적응력승고;령일방면,대직경구배치입확대마촤관구골상가인기관내벽파손돌파,도치응력(포괄압응력급전절력)증대급집중。유차추단,관구발육불량전관관절치환시응재보증골상포용적전제하선택교대직경적구배,유리우응력적량호분포,단응진량피면혹감소확대마촤관구골상소치관구내벽적천파。
BACKGROUND:The anatomical structure of acetabulum is different for the developmental dysplasia of the hip, which is smal and shal ow, with abundant cal us and scar tissue. It is difficult to determine the diameter of cup and instal ation of the cup during arthroplasty. Loosening and survival of postoperative prosthesis were influenced by local mechanical changes. <br> OBJECTIVE:Using the three-dimensional finite element analysis, the stress distribution in acetabular cup-bone interface after implanting cups with different diameters was studied during total hip replacement in treating the dysplasia of hip. <br> METHODS:Pelvis of developmental dysplasia of the hip patients was selected in this study. Acetabulum in the dysplasia was scanned by spiral CT. The computer simulation technology was applied to reconstruct the three-dimensional model of the pelvic for observing the dysplasia of hip from CT scan picture. Implanting cups with different diameters were simulated. Then the pelvis and acetabular cup model were meshed. The mechanics analysis tool was used to analyze three-dimensional model. <br> RESULTS AND CONCLUSION:For the developmental dysplasia, we chose cup with smal diameter that could lead to better bone bed inclusion of cup during total hip replacement. Smal diameter cup induced a smal contact area and increased unit area stress. On the other hand, with implanting the larger cup and increasing degree of acetabular grinding, the acetabular wal bone breaks more obvious, so that the stress (compressive stress and shearing force) concentration at the top of the acetabulum and uneven stress in the rest were apparent increasingly. Thus, in clinical practice, under the premise of the bone bed inclusion, a large diameter cup is helpful to good distribution of stress during total hip replacement, but the perforation of acetabular wal induced by enlarged bone bed should be avoided or minimized.