陶瓷学报
陶瓷學報
도자학보
JOURNAL OF CERAMICS
2014年
3期
304-308
,共5页
朱小平%梁耀龙%刘俊荣%于长凤%张缇
硃小平%樑耀龍%劉俊榮%于長鳳%張緹
주소평%량요룡%류준영%우장봉%장제
CaTiO3:Pr3+%红色蓄能发光材料%余辉时间%激活剂
CaTiO3:Pr3+%紅色蓄能髮光材料%餘輝時間%激活劑
CaTiO3:Pr3+%홍색축능발광재료%여휘시간%격활제
CaTiO3:Pr3+red long-afterglow phosphors%decay time%activating agent
以碳酸钙、氧化锌、二氧化钛为主要原料,以氧化镨为激活剂,以氧化铕为辅助激活剂,以碳酸钠为电荷补偿剂,以硼酸为助熔剂,采用高温固相法对红色CaTiO3:Pr3+蓄光材料进行了试制研究。试制得到荧光余辉时间达20 min左右、发光效果良好的CaTiO3:Pr3+系红色荧光材料。对合成的荧光粉末进行了XRD、激发光谱分析检测,表明合成所得荧光粉的主晶相为CaTiO3。试验结果表明,在配料组成确定后,合成温度和保温时间对发光效果的影响较大。当合成温度为1100℃,保温时间为2h制备得到的荧光材料发光效果良好。
以碳痠鈣、氧化鋅、二氧化鈦為主要原料,以氧化鐠為激活劑,以氧化銪為輔助激活劑,以碳痠鈉為電荷補償劑,以硼痠為助鎔劑,採用高溫固相法對紅色CaTiO3:Pr3+蓄光材料進行瞭試製研究。試製得到熒光餘輝時間達20 min左右、髮光效果良好的CaTiO3:Pr3+繫紅色熒光材料。對閤成的熒光粉末進行瞭XRD、激髮光譜分析檢測,錶明閤成所得熒光粉的主晶相為CaTiO3。試驗結果錶明,在配料組成確定後,閤成溫度和保溫時間對髮光效果的影響較大。噹閤成溫度為1100℃,保溫時間為2h製備得到的熒光材料髮光效果良好。
이탄산개、양화자、이양화태위주요원료,이양화보위격활제,이양화유위보조격활제,이탄산납위전하보상제,이붕산위조용제,채용고온고상법대홍색CaTiO3:Pr3+축광재료진행료시제연구。시제득도형광여휘시간체20 min좌우、발광효과량호적CaTiO3:Pr3+계홍색형광재료。대합성적형광분말진행료XRD、격발광보분석검측,표명합성소득형광분적주정상위CaTiO3。시험결과표명,재배료조성학정후,합성온도화보온시간대발광효과적영향교대。당합성온도위1100℃,보온시간위2h제비득도적형광재료발광효과량호。
A series of tests were developed around CaTiO3:Pr3+red lfuorescent material. In this study, CaTiO3:Pr3+red persistent phosphors with good glowing effect and about 20 minutes’ decay time were prepared by high-temperature solid-phase method with CaCO3, ZnO, TiO2 as main raw materials, Pr2O3 as the activate agent, Eu2O3 as auxiliary activators, Na2CO3 as compensate for the charge, as lfux.Samples were characterized by means of powder X-ray diffraction (XRD) and laser spectral analysis. Result showed that main phase of the synthesized lfuorescent powder was CaTiO3:Pr3+. Results shown that glowing effect were signiifcantly inlfuenced by synthesis temperature and the soaking time, when composition determined, Optimum synthetic temperature was 1100℃, and soaking time was 2 hours..