炼油技术与工程
煉油技術與工程
련유기술여공정
PETROLEUM REFINERY ENGINEERING
2014年
6期
42-44
,共3页
复式波纹管膨胀节%设计%位移附加值%EJMA%应力
複式波紋管膨脹節%設計%位移附加值%EJMA%應力
복식파문관팽창절%설계%위이부가치%EJMA%응력
dual%bellows%expansion%joint%design%additional%movement%EJMA%stress
《美国膨胀节制造商协会标准》EJMA-2003对复式膨胀节中间管引起的膨胀节位移附加值计算作出了规定,要求在计算最大单波组合位移时加以考虑,而国内标准中并没有对此部分内容提出要求.由于波纹管的应力主要由内外压和位移引起,位移产生的应力通常大于内外压引起的应力.当复式膨胀节中间管较长,口径较大,结构较重时,对波纹管会引起较大的附加位移,最大组合位移超出设计值.因此在设计复式波纹管膨胀节时要充分考虑膨胀节上各种构件自身结构重量引起波纹管附加位移的情况,再按照国标规定进行波纹管的强度、稳定性及疲劳寿命的计算,做好膨胀节设计,确保其在装置中正常运行.
《美國膨脹節製造商協會標準》EJMA-2003對複式膨脹節中間管引起的膨脹節位移附加值計算作齣瞭規定,要求在計算最大單波組閤位移時加以攷慮,而國內標準中併沒有對此部分內容提齣要求.由于波紋管的應力主要由內外壓和位移引起,位移產生的應力通常大于內外壓引起的應力.噹複式膨脹節中間管較長,口徑較大,結構較重時,對波紋管會引起較大的附加位移,最大組閤位移超齣設計值.因此在設計複式波紋管膨脹節時要充分攷慮膨脹節上各種構件自身結構重量引起波紋管附加位移的情況,再按照國標規定進行波紋管的彊度、穩定性及疲勞壽命的計算,做好膨脹節設計,確保其在裝置中正常運行.
《미국팽창절제조상협회표준》EJMA-2003대복식팽창절중간관인기적팽창절위이부가치계산작출료규정,요구재계산최대단파조합위이시가이고필,이국내표준중병몰유대차부분내용제출요구.유우파문관적응력주요유내외압화위이인기,위이산생적응력통상대우내외압인기적응력.당복식팽창절중간관교장,구경교대,결구교중시,대파문관회인기교대적부가위이,최대조합위이초출설계치.인차재설계복식파문관팽창절시요충분고필팽창절상각충구건자신결구중량인기파문관부가위이적정황,재안조국표규정진행파문관적강도、은정성급피로수명적계산,주호팽창절설계,학보기재장치중정상운행.