耐火材料
耐火材料
내화재료
REFRACTORIES
2010年
1期
30-33
,共4页
徐延庆%吕世坪%范志辉%王金相%洪彦若%陈肇友
徐延慶%呂世坪%範誌輝%王金相%洪彥若%陳肇友
서연경%려세평%범지휘%왕금상%홍언약%진조우
氢氧化铬溶胶%纳米氧化铬%致密氧化铬材料%烧结%致密化%微气孔
氫氧化鉻溶膠%納米氧化鉻%緻密氧化鉻材料%燒結%緻密化%微氣孔
경양화락용효%납미양화락%치밀양화락재료%소결%치밀화%미기공
在氧化铬材料中分别引入0.3%、0.6%、0.9%和1.2%(按Cr2O3的质量分数计)的纳米Cr2O3前驱体--氢氧化铬溶胶,通过喷雾造粒、等静压成型,将制备的致密氧化铬试样在氮气气氛中分别于1 350、1 400、1 450 ℃下烧成后,测定烧后试样的显气孔率和常温抗折强度,并采用SEM分析烧成后试样的显微结构.结果表明:加入氢氧化铬溶胶促进了致密氧化铬材料的烧结,其加入量为w(Cr2O3)=0.3%时,材料中的气孔明显减少,常温抗折强度显著提高;加入适量氢氧化铬溶胶促进了材料的烧结致密化,使试样结构更加致密,气孔呈微细化均匀分布.
在氧化鉻材料中分彆引入0.3%、0.6%、0.9%和1.2%(按Cr2O3的質量分數計)的納米Cr2O3前驅體--氫氧化鉻溶膠,通過噴霧造粒、等靜壓成型,將製備的緻密氧化鉻試樣在氮氣氣氛中分彆于1 350、1 400、1 450 ℃下燒成後,測定燒後試樣的顯氣孔率和常溫抗摺彊度,併採用SEM分析燒成後試樣的顯微結構.結果錶明:加入氫氧化鉻溶膠促進瞭緻密氧化鉻材料的燒結,其加入量為w(Cr2O3)=0.3%時,材料中的氣孔明顯減少,常溫抗摺彊度顯著提高;加入適量氫氧化鉻溶膠促進瞭材料的燒結緻密化,使試樣結構更加緻密,氣孔呈微細化均勻分佈.
재양화락재료중분별인입0.3%、0.6%、0.9%화1.2%(안Cr2O3적질량분수계)적납미Cr2O3전구체--경양화락용효,통과분무조립、등정압성형,장제비적치밀양화락시양재담기기분중분별우1 350、1 400、1 450 ℃하소성후,측정소후시양적현기공솔화상온항절강도,병채용SEM분석소성후시양적현미결구.결과표명:가입경양화락용효촉진료치밀양화락재료적소결,기가입량위w(Cr2O3)=0.3%시,재료중적기공명현감소,상온항절강도현저제고;가입괄량경양화락용효촉진료재료적소결치밀화,사시양결구경가치밀,기공정미세화균균분포.