塑料工业
塑料工業
소료공업
CHINA PLASTICS INDUSTRY
2013年
4期
23-25
,共3页
刘志林%汪克风%张海勇%刘珍元%白福青
劉誌林%汪剋風%張海勇%劉珍元%白福青
류지림%왕극풍%장해용%류진원%백복청
尼龙6/丙烯腈-丁二烯-苯乙烯共聚物合金%相容剂%增韧剂%缺口冲击强度
尼龍6/丙烯腈-丁二烯-苯乙烯共聚物閤金%相容劑%增韌劑%缺口遲擊彊度
니룡6/병희정-정이희-분을희공취물합금%상용제%증인제%결구충격강도
采用马来酸酐接枝丙烯腈-丁二烯-苯乙烯共聚物(ABS-g-MAH)、马来酸酐接枝乙烯-辛烯共聚物(POE-g-MAH)和苯乙烯-马来酸酐共聚物(SMA)为相容剂,研究了相容剂种类、相容剂含量、增韧剂含量及挤出机螺杆转速对尼龙6/丙烯腈-丁二烯-苯乙烯共聚物(PA6/ABS)合金力学性能的影响.研究表明,ABS-g-MAH为PA6/ABS合金的最佳相容剂,且质量分数为20%时合金的缺口冲击强度最高;采用ABS-g-MAH和POE-g-MAH复合增容增韧可得到力学性能优越的PA6/ABS合金;降低挤出机螺杆转速可使PA6/ABS合金的缺口冲击强度提高.
採用馬來痠酐接枝丙烯腈-丁二烯-苯乙烯共聚物(ABS-g-MAH)、馬來痠酐接枝乙烯-辛烯共聚物(POE-g-MAH)和苯乙烯-馬來痠酐共聚物(SMA)為相容劑,研究瞭相容劑種類、相容劑含量、增韌劑含量及擠齣機螺桿轉速對尼龍6/丙烯腈-丁二烯-苯乙烯共聚物(PA6/ABS)閤金力學性能的影響.研究錶明,ABS-g-MAH為PA6/ABS閤金的最佳相容劑,且質量分數為20%時閤金的缺口遲擊彊度最高;採用ABS-g-MAH和POE-g-MAH複閤增容增韌可得到力學性能優越的PA6/ABS閤金;降低擠齣機螺桿轉速可使PA6/ABS閤金的缺口遲擊彊度提高.
채용마래산항접지병희정-정이희-분을희공취물(ABS-g-MAH)、마래산항접지을희-신희공취물(POE-g-MAH)화분을희-마래산항공취물(SMA)위상용제,연구료상용제충류、상용제함량、증인제함량급제출궤라간전속대니룡6/병희정-정이희-분을희공취물(PA6/ABS)합금역학성능적영향.연구표명,ABS-g-MAH위PA6/ABS합금적최가상용제,차질량분수위20%시합금적결구충격강도최고;채용ABS-g-MAH화POE-g-MAH복합증용증인가득도역학성능우월적PA6/ABS합금;강저제출궤라간전속가사PA6/ABS합금적결구충격강도제고.