口腔医学研究
口腔醫學研究
구강의학연구
JOURNAL OF ORAL SCIENCE RESEARCH
2012年
12期
1221-1224
,共4页
曾智惠%段嫄嫄%靳海立%贺专%贾骏
曾智惠%段嫄嫄%靳海立%賀專%賈駿
증지혜%단원원%근해립%하전%가준
IPS e.max%有限元%强度%厚度比%最优化
IPS e.max%有限元%彊度%厚度比%最優化
IPS e.max%유한원%강도%후도비%최우화
目的:基于非线性接触有限元数值计算方法探讨不同饰瓷与核瓷厚度比对IPS e.max全瓷冠强度的影响.方法:建立5组轴对称下颌第一磨牙形态试件的有限元模型,饰瓷与核瓷厚度比分别为1∶4、1∶2、1∶1、2∶1、4∶1.采用半径为4.5 mm的半球形加载头对各组模型进行加载,得到各组模型在不同载荷下的应力分布状态及变化规律,并通过最优化理论进行分析.结果:饰瓷的最大主应力峰值出现在饰瓷咬合面与加载头接触的外侧周围;核瓷的最大主应力峰值出现在加载头接触区下方的核瓷与粘接剂之间;饰瓷和核瓷所受的最大主应力均随载荷的增大而增加.基于最优化理论饰瓷与核瓷厚度比为1∶4时断裂强度最大.结论:基于本实验有限元模型分析,临床上在满足美观要求的情况下,应尽量减小饰核瓷厚度比,以期增加全瓷冠整体断裂强度,提高使用寿命.
目的:基于非線性接觸有限元數值計算方法探討不同飾瓷與覈瓷厚度比對IPS e.max全瓷冠彊度的影響.方法:建立5組軸對稱下頜第一磨牙形態試件的有限元模型,飾瓷與覈瓷厚度比分彆為1∶4、1∶2、1∶1、2∶1、4∶1.採用半徑為4.5 mm的半毬形加載頭對各組模型進行加載,得到各組模型在不同載荷下的應力分佈狀態及變化規律,併通過最優化理論進行分析.結果:飾瓷的最大主應力峰值齣現在飾瓷咬閤麵與加載頭接觸的外側週圍;覈瓷的最大主應力峰值齣現在加載頭接觸區下方的覈瓷與粘接劑之間;飾瓷和覈瓷所受的最大主應力均隨載荷的增大而增加.基于最優化理論飾瓷與覈瓷厚度比為1∶4時斷裂彊度最大.結論:基于本實驗有限元模型分析,臨床上在滿足美觀要求的情況下,應儘量減小飾覈瓷厚度比,以期增加全瓷冠整體斷裂彊度,提高使用壽命.
목적:기우비선성접촉유한원수치계산방법탐토불동식자여핵자후도비대IPS e.max전자관강도적영향.방법:건립5조축대칭하합제일마아형태시건적유한원모형,식자여핵자후도비분별위1∶4、1∶2、1∶1、2∶1、4∶1.채용반경위4.5 mm적반구형가재두대각조모형진행가재,득도각조모형재불동재하하적응력분포상태급변화규률,병통과최우화이론진행분석.결과:식자적최대주응력봉치출현재식자교합면여가재두접촉적외측주위;핵자적최대주응력봉치출현재가재두접촉구하방적핵자여점접제지간;식자화핵자소수적최대주응력균수재하적증대이증가.기우최우화이론식자여핵자후도비위1∶4시단렬강도최대.결론:기우본실험유한원모형분석,림상상재만족미관요구적정황하,응진량감소식핵자후도비,이기증가전자관정체단렬강도,제고사용수명.