华东交通大学学报
華東交通大學學報
화동교통대학학보
JOURNAL OF EAST CHINA JIAOTONG UNIVERSITY
2013年
5期
18-23
,共6页
王旭%赵秀绍%艾成刚%莫林利
王旭%趙秀紹%艾成剛%莫林利
왕욱%조수소%애성강%막림리
击实试验%最大干密度%“精确边击边测”%余土高度%数据处理
擊實試驗%最大榦密度%“精確邊擊邊測”%餘土高度%數據處理
격실시험%최대간밀도%“정학변격변측”%여토고도%수거처리
compaction experiment%maximum dry density%compaction by accurate measuring%soil height%da-ta processing
针对室内标准击实试验,介绍了压实度的确定方法和室内击实试验方法的选用,对影响试验结果的因素进行了说明和分析研究。首先对试验用土提出了要求,其次提出了击实土余土高度控制在6 mm内的“精确边击边测”的控制方法,控制每层土样击实后厚度约为三分之一筒高,当超过或欠缺时,应适当的减小或增加下层土的加入量,实践表明“精确边击边测”的控制方法可以有效的控制余土高度在6 mm以内。实验数据的处理借助Excel和Matlab软件,分别采用三点二次和更高次的Lagrange插值对最大干密度与最佳含水率进行求解。计算结果表明,并非选取的插值点越多、拟合曲线次数越高,就能达到更高的准确性,采用合理的三点二次的Lagrange插值法就可得到准确的计算结果。
針對室內標準擊實試驗,介紹瞭壓實度的確定方法和室內擊實試驗方法的選用,對影響試驗結果的因素進行瞭說明和分析研究。首先對試驗用土提齣瞭要求,其次提齣瞭擊實土餘土高度控製在6 mm內的“精確邊擊邊測”的控製方法,控製每層土樣擊實後厚度約為三分之一筒高,噹超過或欠缺時,應適噹的減小或增加下層土的加入量,實踐錶明“精確邊擊邊測”的控製方法可以有效的控製餘土高度在6 mm以內。實驗數據的處理藉助Excel和Matlab軟件,分彆採用三點二次和更高次的Lagrange插值對最大榦密度與最佳含水率進行求解。計算結果錶明,併非選取的插值點越多、擬閤麯線次數越高,就能達到更高的準確性,採用閤理的三點二次的Lagrange插值法就可得到準確的計算結果。
침대실내표준격실시험,개소료압실도적학정방법화실내격실시험방법적선용,대영향시험결과적인소진행료설명화분석연구。수선대시험용토제출료요구,기차제출료격실토여토고도공제재6 mm내적“정학변격변측”적공제방법,공제매층토양격실후후도약위삼분지일통고,당초과혹흠결시,응괄당적감소혹증가하층토적가입량,실천표명“정학변격변측”적공제방법가이유효적공제여토고도재6 mm이내。실험수거적처리차조Excel화Matlab연건,분별채용삼점이차화경고차적Lagrange삽치대최대간밀도여최가함수솔진행구해。계산결과표명,병비선취적삽치점월다、의합곡선차수월고,취능체도경고적준학성,채용합리적삼점이차적Lagrange삽치법취가득도준학적계산결과。
This paper discusses how to determine compaction degrees and how to choose laboratory compac-tion experiments,then analyzes the factors that influence the experiment results. Firstly,the requirements for the experiment soil are set forth;Secondly,in order to control the excess height of soil column within 6mm,an experiment method called“controlling the excess height of soil column with compaction by accurate measur-ing”is proposed to control the thickness of each layer of soil sample reaching about one-third of the tube after compaction. When the height of each layer is higher or lower than one-third of the tube,the amount of added soil in the next step should be decreased or increased accordingly. The empirical study shows this method can effectively control the excess height of soil column within 6mm. In addition,with the aid of Excelland Matlab software,Lagrange interpolated with quadratic polynomial and high order polynomial is adopted to get the max-imum dry density and optimum moisture content. Results suggest that the accuracy of the result is not related to the numbers of interpolation points and high-order curve-fitting. Instead,Lagrange interpolated with quadratic polynomial in which three number points are reasonably selected will lead to accurate calculation results.