热喷涂技术
熱噴塗技術
열분도기술
THERMAL SPRAY TECHNOLOGY
2012年
2期
35-43
,共9页
韩志海%王海军%白宇%徐艳莉%刘明%徐超%李红强%王政
韓誌海%王海軍%白宇%徐豔莉%劉明%徐超%李紅彊%王政
한지해%왕해군%백우%서염리%류명%서초%리홍강%왕정
大气等离子体喷涂%喷涂粒子%加热历程%熔化状态
大氣等離子體噴塗%噴塗粒子%加熱歷程%鎔化狀態
대기등리자체분도%분도입자%가열역정%용화상태
Supersonic atmospheric plasma spraying%Refinement%Plasma jet%Molten state
本文通过对水中收集的等离子喷涂熔融粒子进行粒度分析及形貌观察,研究了喷涂粒子在普通大气等离子喷涂(APS)及超音速大气等离子喷涂(SAPS)射流中的加热历程及熔化状态。实验观察到氧化钇部分稳定的纳米颗粒团聚造粒的氧化锆(Y—PSZ)球形粉末颗粒在APS及SAPS射流中传热传质过程中的熔融与“细化”现象有明显不同:在SAPS射流中,尺寸较大(粒径在几十微米)的颗粒大部分形成了十分细小的(小于5μm)颗粒;相对而言,APS中的熔融粒子仍以十几微米以上较大粒径的半熔融粒子为主。进一步研究表明,大尺寸粒子在等离子射流中先从表层熔化,逐渐向颗粒内部扩展,形成柱晶熔区,属典型的梯度熔化模式,最终芯部存留大量细小未熔一次粒子,即所谓半熔融状态;相应的SAPS中大量粒径小于5μm的小颗粒在超音速等离子体射流中整体迅速熔化(即所谓等温熔化模式)。对熔融或半熔融粒子撞击基体后的扁平化过程进行分析表明:在APS射流中扁平粒子的直径一般在100μm以上,且周围飞溅较多,导致典型的层状多孔的粗大组织结构,层间出现较多平行横向裂纹;而SAPS大量细小熔滴撞击基体后,冷却更快,多呈无明显飞溅的直径约10-30μm圆盘状,形成大量细密柱晶交错堆垛而成的、无明显分层的特殊结构。对收集粒子进行X-射线衍射相分析表明,APS及SAPS两种工艺下的熔融粒子均未发生明显相变,相组成主要为室温下非转变四方氧化锆(t’-ZrO2),说明喷涂粒子在高温等离子射流的加热历程中,其晶体结构和化学成分未发生明显变化。
本文通過對水中收集的等離子噴塗鎔融粒子進行粒度分析及形貌觀察,研究瞭噴塗粒子在普通大氣等離子噴塗(APS)及超音速大氣等離子噴塗(SAPS)射流中的加熱歷程及鎔化狀態。實驗觀察到氧化釔部分穩定的納米顆粒糰聚造粒的氧化鋯(Y—PSZ)毬形粉末顆粒在APS及SAPS射流中傳熱傳質過程中的鎔融與“細化”現象有明顯不同:在SAPS射流中,呎吋較大(粒徑在幾十微米)的顆粒大部分形成瞭十分細小的(小于5μm)顆粒;相對而言,APS中的鎔融粒子仍以十幾微米以上較大粒徑的半鎔融粒子為主。進一步研究錶明,大呎吋粒子在等離子射流中先從錶層鎔化,逐漸嚮顆粒內部擴展,形成柱晶鎔區,屬典型的梯度鎔化模式,最終芯部存留大量細小未鎔一次粒子,即所謂半鎔融狀態;相應的SAPS中大量粒徑小于5μm的小顆粒在超音速等離子體射流中整體迅速鎔化(即所謂等溫鎔化模式)。對鎔融或半鎔融粒子撞擊基體後的扁平化過程進行分析錶明:在APS射流中扁平粒子的直徑一般在100μm以上,且週圍飛濺較多,導緻典型的層狀多孔的粗大組織結構,層間齣現較多平行橫嚮裂紋;而SAPS大量細小鎔滴撞擊基體後,冷卻更快,多呈無明顯飛濺的直徑約10-30μm圓盤狀,形成大量細密柱晶交錯堆垛而成的、無明顯分層的特殊結構。對收集粒子進行X-射線衍射相分析錶明,APS及SAPS兩種工藝下的鎔融粒子均未髮生明顯相變,相組成主要為室溫下非轉變四方氧化鋯(t’-ZrO2),說明噴塗粒子在高溫等離子射流的加熱歷程中,其晶體結構和化學成分未髮生明顯變化。
본문통과대수중수집적등리자분도용융입자진행립도분석급형모관찰,연구료분도입자재보통대기등리자분도(APS)급초음속대기등리자분도(SAPS)사류중적가열역정급용화상태。실험관찰도양화을부분은정적납미과립단취조립적양화고(Y—PSZ)구형분말과립재APS급SAPS사류중전열전질과정중적용융여“세화”현상유명현불동:재SAPS사류중,척촌교대(립경재궤십미미)적과립대부분형성료십분세소적(소우5μm)과립;상대이언,APS중적용융입자잉이십궤미미이상교대립경적반용융입자위주。진일보연구표명,대척촌입자재등리자사류중선종표층용화,축점향과립내부확전,형성주정용구,속전형적제도용화모식,최종심부존류대량세소미용일차입자,즉소위반용융상태;상응적SAPS중대량립경소우5μm적소과립재초음속등리자체사류중정체신속용화(즉소위등온용화모식)。대용융혹반용융입자당격기체후적편평화과정진행분석표명:재APS사류중편평입자적직경일반재100μm이상,차주위비천교다,도치전형적층상다공적조대조직결구,층간출현교다평행횡향렬문;이SAPS대량세소용적당격기체후,냉각경쾌,다정무명현비천적직경약10-30μm원반상,형성대량세밀주정교착퇴타이성적、무명현분층적특수결구。대수집입자진행X-사선연사상분석표명,APS급SAPS량충공예하적용융입자균미발생명현상변,상조성주요위실온하비전변사방양화고(t’-ZrO2),설명분도입자재고온등리자사류적가열역정중,기정체결구화화학성분미발생명현변화。
In this work, the particles were collected in the water and the heat process and molten state of particles in plasma jet were studied. The results revealed that the YSZ particles were refined in the APS and SAPS plasma jet, however, this phenomenon was more significant in the latter, leading to the formation of numerous fine particles with size less than 5 μ m. In addition, three molten states were found for the particles in the SAPS plasma jet, they are 1 ) un-melted state; 2) partially melted state, which corresponded to the gradient melting mode; 3 ) fully molten state for the fine particles, which corresponded to the isothermal melting mode. For the APS process, the diameter of splating particles after the in-flight particle impinged onto the substrate was more than 100 IJ m and the splash formed around the splat, however, the splash was not found around the small splat (about diameter of 10-30 ~ m)formed by the fine molten particle in the SAPS plasma jet, as a result, the microstructure of SAPS-coating was much finer than that of APS-coating. Meanwhile, the original and collected particles were composed of t'-ZrOz, which suggested the compositions (especially the Y203) of powders in the APS/SAPS plasma jets were not changed.