电子测试
電子測試
전자측시
ELECTRONIC TEST
2012年
8期
52-55
,共4页
安慰东%刘杰%包德州%刘平安
安慰東%劉傑%包德州%劉平安
안위동%류걸%포덕주%류평안
纳伏级微弱信号%低噪声差分放大电路%多级滤波%信噪比
納伏級微弱信號%低譟聲差分放大電路%多級濾波%信譟比
납복급미약신호%저조성차분방대전로%다급려파%신조비
the weak signal of Nan voltmeter level%low noise differential signal amplifier%multi-level filtering%SNR
针对工程测量领域的实际需求,设计了纳伏级微弱信号的放大电路,在信号输入端,通过仿真软件仿真设计,最终选用AD公司的超低噪声差分信号放大芯片AD620,放大倍数为10倍,降低了等效输入噪声。设计了相应的信号调理电路,采用多级放大电路组态方式,运用超低噪声四运放(OP470A)来组建多级带通滤波器,经过多级滤波、多级放大,逐步提高信噪比。通过实验,采用不同频段的噪声,验证SNR的改善情况。利用Multisim仿真软件对系统噪声进行了分析,分析结果显示,在低频段有效地抑制对电路造成影响的各种噪声,信噪比得到了较大的提升。
針對工程測量領域的實際需求,設計瞭納伏級微弱信號的放大電路,在信號輸入耑,通過倣真軟件倣真設計,最終選用AD公司的超低譟聲差分信號放大芯片AD620,放大倍數為10倍,降低瞭等效輸入譟聲。設計瞭相應的信號調理電路,採用多級放大電路組態方式,運用超低譟聲四運放(OP470A)來組建多級帶通濾波器,經過多級濾波、多級放大,逐步提高信譟比。通過實驗,採用不同頻段的譟聲,驗證SNR的改善情況。利用Multisim倣真軟件對繫統譟聲進行瞭分析,分析結果顯示,在低頻段有效地抑製對電路造成影響的各種譟聲,信譟比得到瞭較大的提升。
침대공정측량영역적실제수구,설계료납복급미약신호적방대전로,재신호수입단,통과방진연건방진설계,최종선용AD공사적초저조성차분신호방대심편AD620,방대배수위10배,강저료등효수입조성。설계료상응적신호조리전로,채용다급방대전로조태방식,운용초저조성사운방(OP470A)래조건다급대통려파기,경과다급려파、다급방대,축보제고신조비。통과실험,채용불동빈단적조성,험증SNR적개선정황。이용Multisim방진연건대계통조성진행료분석,분석결과현시,재저빈단유효지억제대전로조성영향적각충조성,신조비득도료교대적제승。
For the actual needs of the field of engineering measuring,designing an amplification circuit of weak signal which is the Nan voltmeter level.Selecting a low noise differential signal amplifier chip to reduce the equivalent input noise.Also designing the corresponding signal conditioning circuit,Using the multi-stage amplifier circuit mode,after a multi-level filtering,multi-level amplifying,gradually increasing the signal to noise ratio.Through the experiment,using the noise of different frequency bands to verify the improvement of the SNR.And using the Multisim Simulation software to analyze the system noises.Effectively inhibit all kinds of noise in the low-frequency bands,and the signal to noise ratio has been improve more higher.