光学精密工程
光學精密工程
광학정밀공정
OPTICS AND PRECISION ENGINEERING
2013年
8期
2071-2078
,共8页
张勤%徐策%徐晨影%青山尚之
張勤%徐策%徐晨影%青山尚之
장근%서책%서신영%청산상지
超微量点胶%点胶控制%点胶分析%高黏度
超微量點膠%點膠控製%點膠分析%高黏度
초미량점효%점효공제%점효분석%고점도
ultra-micro dispensing%dispensing control%dispensing analysis%high viscosity
针对微装配/密封工程对用胶量超微化(≤1 pL)的需求,提出了一种既适用于接触式点胶,也适用于非接触式点胶的超微量点胶方法.采用移液针穿过装有胶液的玻璃微管,在移液针先端吸附微小胶滴,当移液针先端靠近点胶面时,其先端吸附的微小胶滴与点胶面接触,移液针离开点胶面后,微小胶滴的一部分将残留在点胶面上,实现超微量点胶.通过匹配点胶的参数,实现点胶量的控制.该方法可以适用于任何黏度(1~3.5×105 cP)的胶液、任意空间方向的超精密点胶.实验讨论了移液针直径和点胶距离(移液针先端与点胶面的距离)对点胶性能(胶斑直径)的影响;在此基础上,匹配移液针直径、点胶距离、玻璃微管内径和点胶速度等参数,实现了胶液黏度为971 cP,点胶量为40 fL、170 fL、180 fL在3种亲水性不同的点胶面上的微量点胶;以及胶液黏度为3×104 cP,胶斑直径为243.9 μm时的超微量点胶.实验结果验证了提出方法的可行性.
針對微裝配/密封工程對用膠量超微化(≤1 pL)的需求,提齣瞭一種既適用于接觸式點膠,也適用于非接觸式點膠的超微量點膠方法.採用移液針穿過裝有膠液的玻璃微管,在移液針先耑吸附微小膠滴,噹移液針先耑靠近點膠麵時,其先耑吸附的微小膠滴與點膠麵接觸,移液針離開點膠麵後,微小膠滴的一部分將殘留在點膠麵上,實現超微量點膠.通過匹配點膠的參數,實現點膠量的控製.該方法可以適用于任何黏度(1~3.5×105 cP)的膠液、任意空間方嚮的超精密點膠.實驗討論瞭移液針直徑和點膠距離(移液針先耑與點膠麵的距離)對點膠性能(膠斑直徑)的影響;在此基礎上,匹配移液針直徑、點膠距離、玻璃微管內徑和點膠速度等參數,實現瞭膠液黏度為971 cP,點膠量為40 fL、170 fL、180 fL在3種親水性不同的點膠麵上的微量點膠;以及膠液黏度為3×104 cP,膠斑直徑為243.9 μm時的超微量點膠.實驗結果驗證瞭提齣方法的可行性.
침대미장배/밀봉공정대용효량초미화(≤1 pL)적수구,제출료일충기괄용우접촉식점효,야괄용우비접촉식점효적초미량점효방법.채용이액침천과장유효액적파리미관,재이액침선단흡부미소효적,당이액침선단고근점효면시,기선단흡부적미소효적여점효면접촉,이액침리개점효면후,미소효적적일부분장잔류재점효면상,실현초미량점효.통과필배점효적삼수,실현점효량적공제.해방법가이괄용우임하점도(1~3.5×105 cP)적효액、임의공간방향적초정밀점효.실험토론료이액침직경화점효거리(이액침선단여점효면적거리)대점효성능(효반직경)적영향;재차기출상,필배이액침직경、점효거리、파리미관내경화점효속도등삼수,실현료효액점도위971 cP,점효량위40 fL、170 fL、180 fL재3충친수성불동적점효면상적미량점효;이급효액점도위3×104 cP,효반직경위243.9 μm시적초미량점효.실험결과험증료제출방법적가행성.